SMART ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU |
| CHECK POWER MANAGEMENT CONTROL ECU |

Disconnect the A39, I3 and I4 connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A39-2 (IG2D) - Body ground | Output | R - Body ground | IG2 signal | 20°C (68°F) | Approximately 302.97 Ω | IG2 Relay Monitor(Outside) |
| I4-10 (STP) - Body ground | Input | GR - Body ground | Stop light switch signal | Brake pedal released → Brake pedal depressed | 9 V or higher → 1 V or less | Stop Light Switch1 |
| I3-1 (AM22) - Body ground | Input | SB - Body ground | Power source | Power switch off | 11 to 14 V | - |
| I4-7 (AM21) - Body ground | Input | L - Body ground | Power source | Power switch off | 11 to 14 V | - |
| I4-12 (SLP) - Body ground | Input | P - Body ground | Steering lock position signal | Always | 10 kΩ or higher | Steering Unlock Switch |
| I3-5 (E01) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| I4-5 (E02) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| I3-6 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| I4-4 (E12) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| I4-17 (SSW2) - Body ground | Input | V - Body ground | SSW2 contact signal
| Power switch pushed → Power switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch2 |
| I3-7 (SSW1) - Body ground | Input | R - Body ground | SSW1 contact signal | Power switch pushed → Power switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch1 |
| I4-2 (IG1D) - Body ground | Output | P - Body ground | IG1 signal | 20°C (68°F) | 40.74 to 59.49 Ω | IG1 Relay Monitor(Outside) |
| I4-1 ACCD) - Body ground | Output | W - Body ground | ACC signal | 20°C (68°F) | 81.49 to 118.98 Ω | ACC Relay Monitor |
| I3-16 (SPDI) - I3-6 (E1) | Input | V - BR | Vehicle speed signal | Always | 30 kΩ or higher | Vehicle Speed Signal |
| I4-14 (P2) - I3-6 (E1) | Input | R - BR | P position signal | Always | 40 kΩ or higher → 200 Ω or less | Shift P Signal |
Reconnect the A39, I3 and I4 connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A39-2 (IG2D) - I3-6 (E1) | Output | R - BR | IG2 signal | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher | IG2 Relay Monitor(Outside) |
| I4-12 (SLP) - I3-6 (E1) | Input | P - BR | Steering lock position signal | Steering wheel locked → Steering wheel unlocked*1 | 11 to 14 V → 1.2 V or less | Steering Unlock Switch |
| I4-6 (SLR+) - I3-6 (E1) | Output | SB - BR | Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the power management control ECU) | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*2 | Pulse generation (See waveform 1) | - |
| I4-14 (P2) - I3-6 (E1) | Input | R - BR | P position signal | Shift lever in P → Shift lever not in P | 9 V or higher → 1.5 V or less | Shift P Signal |
| I4-17 (SSW2) - I3-6 (E1) | Input | V - BR | SSW2 contact signal
| Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch2 |
| I3-7 (SSW1) - I3-6 (E1) | Input | R - BR | SSW1 contact signal | Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch1 |
| I4-1 (ACCD) - I3-6 (E1) | Output | W - BR | ACC signal | Power switch off → Power switch on (ACC) | 1 V or less → 8.5 V or higher | ACC Relay Monitor |
| I4-2 (IG1D) - I3-6 (E1) | Output | P - BR | IG1 signal | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher | IG1 Relay Monitor(Outside) |
| I3-16 (SPDI) - I3-6 (E1) | Input | V - BR | Vehicle speed signal | Vehicle being driven at approx. 5 km/h (3 mph) | Pulse generation (See waveform 2) | Vehicle Speed Signal |
Using an oscilloscope, check the waveform of the ECU.
![]() |
Waveform 1
| Item | Content |
| Tester Connection | I4-6 (SLR+) - I3-6 (E1) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped |
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
![]() |
Waveform 2
| Item | Content |
| Tester Connection | I3-16 (SPDI) - I3-6 (E1) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph) |