SMART ENTRY AND START SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Signal | Shift position P/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF | ON: Steering unlocked OFF: Steering locked |
|
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
|
| Start Switch1 | Power switch 1 status/ON or OFF | ON: Power switch pressed OFF: Power switch not pressed |
|
| Start Switch2 | Power switch 2 status/ON or OFF | ON: Power switch pressed OFF: Power switch not pressed |
|
| Latch Circuit | Status of IG related backup circuits/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| IG1 Relay Monitor(Outside) | IG1 relay coil voltage monitor status/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| IG1 Relay Monitor(Inside) | IG1 relay activation/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| IG2 Relay Monitor(Outside) | IG2 relay coil voltage monitor status/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| IG2 Relay Monitor(Inside) | IG2 relay activation/ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| Starter Request Signal | Hybrid control system request signal status/ON or OFF | ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held OFF: After approx. 1 sec. has elapsed, the power switch is released |
|
| ACC Relay Monitor | ACC relay activation/ON or OFF | ON: Power switch on (ACC) OFF: Power switch off |
|
| Ready Signal | Ready signal/ON or OFF | ON: Hybrid control system on (on (READY)) OFF: Hybrid control system off | - |
| Vehicle Speed Signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more | - |
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system request signal | Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
| Powertrain Type | Vehicle identification/HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT or S&S-MMT | HV-AT | - |
| IG1 Circuit | IG1 relay coil circuit malfunction/OK or NG | OK: Circuit normal NG: Circuit malfunctioning |
|
| IG2 Circuit | IG2 relay coil circuit malfunction/OK or NG | OK: Circuit normal NG: Circuit malfunctioning |
|
| Starter SW Sig Mismatch | Power switch signal 1 and 2 do not match/Yes or No | Yes: Switch malfunctioning (power switch signal 1 and 2 do not match) No: Switch normal | The hybrid control system can be started even if the result is Yes. However, emergency hybrid control system off while driving by pressing and holding the power switch and, when the brakes are malfunctioning, emergency hybrid control system by pressing and holding the power switch cannot be performed. |
| Park Signal Mismatch | P position signal malfunction/Yes or No | Yes: Signal malfunction (CAN communication and direct line signal do not match) No: Signal normal | Even when Yes is displayed, it is still possible to turn the power switch off (the power source mode will not be stuck in on (ACC) or on (IG)). |
| Str Lock/Unlock Wait T-Out | Steering lock or unlock malfunction/Yes or No | Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.) No: Lock and unlock normal | When the hybrid control system cannot be started due to a steering lock or unlock malfunction, Yes is displayed. |
| Key Certif Wait T-Out | Key verification malfunction/Yes or No | Yes: Verification error (detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching) No: Verification normal | When the hybrid control system cannot be started due to a key verification error, Yes is displayed. |
| Number of Diagnosis Code | Number of DTCs/0 to 255 | - | - |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Certification ECU (smart key ECU assembly) IG power supply input status/ON or OFF | ON: Power switch on (IG) OFF: Power switch off | When the power switch is on (ACC), OFF is displayed. |
| #Codes | Number of DTCs/0 to 255 | - | - |
| Immobiliser | Hybrid control system immobiliser system determined by certification ECU (smart key ECU assembly)/ Set or Unset | Set: Engine immobiliser system set (hybrid control system prohibited) (power switch off) Unset: Engine immobiliser system unset (hybrid control system permitted) (power switch on (ACC) or on (IG)) | The hybrid control system cannot be started when Set is displayed.
|
| Steering Lock Sleep Cond | Steering lock ECU (steering lock actuator assembly) sleep availability/Yes or No | Yes: Sleep available No: Sleep not available | - |
| Steering Lock Start Cond | Steering lock ECU (steering lock actuator assembly) wake up signal status/Yes or No | Yes: Wake up signal sent No: Wake up signal not sent | - |
| Engine Start Condition | Status of hybrid control system permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG | OK: Hybrid control system permitted NG: Hybrid control system prohibited |
|
| Sensor Value | History of malfunction of position sensor in steering lock ECU (steering lock actuator assembly)/OK or NG(Past) | OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator assembly) does not exist. NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator assembly) being on exists (Under normal operation, neither sensor is on). | When NG (Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator assembly) or the assembly itself may be malfunctioning. |
| Power Supply Short | History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator assembly)/OK or NG(Past) | OK: History of motor power source short does not exist NG(Past): History of motor power source short exists | This item displays history when a malfunction exists in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator assembly). |
| Motor Driver Short | History of malfunction (short) in the steering lock ECU (steering lock actuator assembly) motor circuit (DTC B2781 is stored)./OK or NG(Past) | OK: History of short in the motor circuit does not exist NG(Past): History of short in the motor circuit exists | History of a malfunction in the steering lock motor circuit in the steering lock ECU (steering lock actuator assembly). |
| Lock/Unlock Receive | History of receiving an unlock request signal/Yes or No | Yes: History of receiving an unlock request signal exists No: History of receiving an unlock request signal does not exist | - |
| Lock Bar Stuck Error | History of the steering wheel not being able to unlock properly when the steering lock operates for a certain amount of time/OK or NG(Past) | OK: History of steering lock being stuck does not exist NG(Past): History of steering lock being stuck exists | - |
| Push Start Error | History of push start malfunction due to steering lock ECU (steering lock actuator assembly)/OK or NG(Past) | OK: History of push start malfunction does not exist NG(Past): History of push start malfunction exists | - |
| Engine Start Request | Status of hybrid control system permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG | OK: Signal received NG: Signal not received |
|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG | OK: Verification result normal NG: Verification result abnormal | When NG is displayed:
|
| Unlock Request Receive | Unlock request signal received state/OK or NG | OK: Within 10 sec. of turning the power switch on (IG) or on (ACC), or of an hybrid control system operation being performed NG: Power switch on (IG) or on (ACC), or hybrid control system operation not performed |
|
| Lock Request Receive | Lock request signal received state/OK or NG
| OK: Lock request signal received for 10 sec. of any of the doors being opened with shift lever in P and power switch off. NG: Except above | If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| L Code Check(Past) | Verification result history between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)/OK or NG(Past) | OK: History of abnormal verification result does not exist NG(Past): History of abnormal verification result exists | - |
| Steering Lock | Steering lock ECU (steering lock actuator assembly) lock confirmation status/Set or Unset | Set: Lock confirmed Unset: Lock not confirmed | When Unset is displayed, the steering wheel is not locked. |
| Steering Unlock | Steering lock ECU (steering lock actuator assembly) unlock confirmation status/Set or Unset | Set: Unlock confirmed Unset: Unlock not confirmed | When Unset is displayed, the steering wheel is not locked (the hybrid control system cannot be started). |
| Engine Start Indicator | Smart warning light / ON or OFF | Customization status displayed | - |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost same as actual vehicle speed (Speedometer tester) | - |
| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| P Supply for Steering Lock | Smart key ECU assembly | ON/OFF
| When performing this Active Test, make sure the following condition is met: The power switch is on (IG). |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power/Engine SW Light | Power switch light | OFF/ON | When performing this Active Test, make sure the following condition is met: The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running. |