SMART ENTRY AND START SYSTEM (for Entry Function) > Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment |

| 1.READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR OPEN MODE) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Trunk Open Mode | Luggage door opening switch assembly / ON or OFF | Customization status displayed | - |
| Result | Proceed to |
| Entry luggage compartment door open mode is ON | A |
| Entry luggage compartment door open mode is OFF | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (LUGGAGE DOOR OPENING SWITCH ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Tr/B-Door Unlock SW | Luggage compartment door opener outer switch / ON or OFF | ON: Luggage compartment door opener outer switch pushed OFF: Luggage compartment door opener outer switch not pushed | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Trunk and Back-door Open | Operate luggage compartment door lock motor | ON/OFF | - |
|
| ||||
| OK | |
| 4.CHECK WAVE ENVIRONMENT |
![]() |
Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment open function check.
| *a | Approximately 0.3 m (0.984 ft.) |
|
| ||||
| OK | ||
| ||
| 5.CHECK KEY DIAGNOSTIC MODE |
Check the following antennas in the key diagnostic mode (Click here).
![]() |
Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
| *a | 0.7 to 1.0 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA) |
Disconnect the O2 certification ECU (smart key ECU assembly) connector.
Disconnect the T11 electrical key antenna (outside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O2-1 (CG8B) - T11-2 (CLGB) | Always | Below 1 Ω |
| O2-2 (CLG8) - T11-1 (CLG5) | Always | Below 1 Ω |
| O2-1 (CG8B) or T11-2 (CLGB) - Body ground | Always | 10 kΩ or higher |
| O2-2 (CLG8) or T11-1 (CLG5) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) |
![]() |
Remove the outside electrical key antenna (outside luggage) (Click here)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (CLG5) - 2 (CLGB) | Always | Below 1 Ω |
| *a | Component without harness connected: (Electrical Key Antenna (Outside Luggage)) |
|
| ||||
| OK | ||
| ||
| 8.INSPECT LUGGAGE DOOR OPENING SWITCH ASSEMBLY |
Remove the luggage door opening switch assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (E) - 3 (UL) | Luggage door opening switch assembly not pushed | 10 kΩ or higher |
| 2 (E) - 3 (UL) | Luggage door opening switch assembly pushed | Below 1 Ω |
| *a | Component without harness connected (Luggage Door Opening Switch Assembly) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OPENING SWITCH) |
Disconnect the O2 certification ECU (smart key ECU assembly) connector.
Disconnect the T4 luggage door opening switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O2-22 (TSW5) - T4-3 (UL) | Always | Below 1 Ω |
| O2-22 (TSW5) or T4-3 (UL) - Body ground | Always | 10 kΩ or higher |
| T4-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 10.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY |
![]() |
Remove the luggage compartment door lock assembly (Click here).
Check the operation of the door lock motor.
Move the door lock to the close (lock) position.
Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Auxiliary battery positive (+) → 1 (B) Auxiliary battery negative (-) → 2 (E) | Luggage compartment door lock motor open (unlock) operation |
| *a | Component without harness connected: (Luggage Compartment Door Lock Assembly) |
| *b | Close (Lock) |
| *c | Open (Unlock) |
![]() |
Check the door courtesy light switch.
Move the door lock to the close (lock) position.
Measure the resistance according to the value(s) in the table below.
| Measurement Condition | Door Lock Condition | Specified Condition |
| 2 (E) - 3 (D+) | Close (Lock) | 10 kΩ or higher |
| 2 (E) - 3 (D+) | Open (Unlock) | Below 1 Ω |
| *a | Component without harness connected (Luggage Compartment Door Lock Assembly) |
| *b | Close (Lock) |
| *c | Open (Unlock) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR LOCK - INSTRUMENT PANEL JUNCTION BLOCK) |
Luggage compartment door lock motor:
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the T3 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T3-2 (E) - Body ground | Always | Below 1 Ω |
| 3C-10 (TR+) - T3-1 (B) | Always | Below 1 Ω |
| 3C-10 (TR+) or T3-1 (B) - Body ground | Always | 10 kΩ or higher |
Luggage door courtesy light switch:
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the T3 luggage compartment door lock assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T3-2 (E) - Body ground | Always | Below 1 Ω |
| 3C-9 (LGCY) - T3-3 (D+) | Always | Below 1 Ω |
| 3C-9 (LGCY) or T3-3 (D+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Temporarily replace the instrument panel junction block assembly with a new one (Click here).
| NEXT | |
| 13.CHECK OPERATION |
Check that the luggage compartment door entry unlock functions operate normally (Click here).
|
| ||||
| OK | ||
| ||