Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
  3. Turn the power switch off before inspecting CAN bus lines for a ground short.
  4. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  5. This section describes the standard values for all CAN related components.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


CAN JUNCTION RH CONNECTOR (for LHD)


  1. Check the CAN junction RH connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C248091E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN Junction RH Connector)
      *b
      to ECM
      (for V bus)
      *c
      to Air Conditioning Amplifier Assembly
      (for V bus)
      *d
      to Airbag Sensor Assembly
      (for V bus)
      *e
      to Smart Key ECU Assembly (Certification ECU)
      (for V bus)
      *f
      to Power Steering ECU Assembly
      (for V bus)
      *g
      to Radio and Display Receiver Assembly
      (for V bus)
      *h
      to CAN Junction LH Connector
      (for V bus)

    2. Check the connection diagram of the components which are connected to the CAN junction RH connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I104-1 (CANH)
      P
      ECM
      (for V bus)
      I104-2 (CANL)
      W
      I102-1 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      I102-2 (CANL)
      W
      I99-1 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I99-2 (CANL)
      W
      I106-1 (CANH)
      L
      Smart key ECU assembly (Certification ECU)
      (for V bus)
      I106-2 (CANL)
      W
      I98-1 (CANH)
      G
      Power steering ECU assembly
      (for V bus)
      I98-2 (CANL)
      W
      I107-1 (CANH)
      R
      Radio and display receiver assembly
      (for V bus)
      I107-2 (CANL)
      W
      I101-1 (CANH)
      B
      CAN junction LH connector
      (for V bus)
      I101-2 (CANL)
      W


CAN JUNCTION RH CONNECTOR (for RHD)


  1. Check the CAN junction RH connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C248091E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN Junction RH Connector)
      *b
      to Clearance Warning ECU Assembly
      (for V bus)
      *c
      to Steering Sensor
      (for V bus)
      *d
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for V bus)
      *e
      to Smart Key ECU Assembly (Certification ECU)
      (for V bus)
      *f
      to DLC3
      (for V bus)
      *g
      to Combination Meter Assembly
      (for V bus)
      *h
      to CAN Junction LH Connector
      (for V bus)

    2. Check the connection diagram of the components which are connected to the CAN junction RH connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I111-1 (CANH)
      P
      Clearance warning ECU assembly
      (for V bus)
      I111-2 (CANL)
      W
      I97-1 (CANH)
      V
      Steering sensor
      (for V bus)
      I97-2 (CANL)
      W
      I110-1 (CANH)
      Y
      Brake booster with master cylinder assembly (Skid control ECU)
      (for V bus)
      I110-2 (CANL)
      W
      I106-1 (CANH)
      L
      Smart key ECU assembly (Certification ECU)
      (for V bus)
      I106-2 (CANL)
      W
      I96-1 (CANH)
      G
      DLC3
      (for V bus)
      I96-2 (CANL)
      W
      I94-1 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I94-2 (CANL)
      W
      I101-1 (CANH)
      B
      CAN junction LH connector
      (for V bus)
      I101-2 (CANL)
      W


CAN JUNCTION LH CONNECTOR (for LHD)


  1. Check the CAN junction LH connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C248091E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN Junction LH Connector)
      *b
      to Main Body ECU (Multiplex Network Body ECU)
      (for V bus)
      *c
      to Steering Sensor
      (for V bus)
      *d
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for V bus)
      *e
      to DLC3
      (for V bus)
      *f
      to Power Management Control ECU
      (for V bus)
      *g
      to Combination Meter Assembly
      (for V bus)
      *h
      to CAN Junction RH Connector
      (for V bus)

    2. Check the connection diagram of the components which are connected to the CAN junction LH connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I95-1 (CANH)
      P
      Main body ECU (multiplex network body ECU)
      (for V bus)
      I95-2 (CANL)
      W
      I97-1 (CANH)
      V
      Steering sensor
      (for V bus)
      I97-2 (CANL)
      W
      I110-1 (CANH)
      Y
      Brake booster with master cylinder assembly (Skid control ECU)
      (for V bus)
      I110-2 (CANL)
      W
      I96-1 (CANH)
      L
      DLC3
      (for V bus)
      I96-2 (CANL)
      W
      I109-1 (CANH)
      G
      Power management control ECU
      (for V bus)
      I109-2 (CANL)
      W
      I94-1 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I94-2 (CANL)
      W
      I93-1 (CANH)
      B
      CAN junction RH connector
      (for V bus)
      I93-2 (CANL)
      W


CAN JUNCTION LH CONNECTOR (for RHD)


  1. Check the CAN junction LH connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C239444E05


      Text in Illustration 
      *a
      Component with harness connected
      (CAN Junction LH Connector)
      *b
      to Power Management Control ECU
      (for V bus)
      *c
      to Main Body ECU (Multiplex Network Body ECU)
      (for V bus)
      *d
      to Air Conditioning Amplifier Assembly
      (for V bus)
      *e
      to Airbag Sensor Assembly
      (for V bus)
      *f
      to Power Steering ECU Assembly
      (for V bus)
      *g
      to ECM
      (for V bus)
      *h
      to Radio and Display Receiver Assembly
      (for V bus)
      *i
      to CAN Junction RH Connector
      (for V bus)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction LH connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I109-1 (CANH)
      BE
      Power management control ECU
      (for V bus)
      I109-2 (CANL)
      W
      I95-1 (CANH)
      P
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      I95-2 (CANL)
      W
      I102-1 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      I102-2 (CANL)
      W
      I103-1 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I103-2 (CANL)
      W
      I100-1 (CANH)
      L
      Power steering ECU assembly
      (for V bus)
      I100-2 (CANL)
      W
      I104-1 (CANH)
      G
      ECM
      (for V bus)
      I104-2 (CANL)
      W
      I107-1 (CANH)
      R
      Radio and display receiver assembly
      (for V bus)
      I107-2 (CANL)
      W
      I93-1 (CANH)
      B
      CAN junction RH connector
      (for V bus)
      I93-2 (CANL)
      W


CAN NO. 1 JUNCTION CONNECTOR


  1. Check the CAN No. 1 junction connector.



    1. Connection diagram


      C234761E34


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 1 Junction Connector)
      *b
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for Sub bus 15)
      *c
      to ECM
      (for Sub bus 15)
      *d
      to Power Management Control ECU
      (for Sub bus 15)

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      A72-1 (CANH)
      B
      Brake booster with master cylinder assembly (Skid control ECU)
      (for Sub bus 15)
      A72-7 (CANL)
      W
      A72-2 (CANH)
      B
      ECM
      (for Sub bus 15)
      A72-8 (CANL)
      W
      A72-3 (CANH)
      B
      Power management control ECU
      (for Sub bus 15)
      A72-9 (CANL)
      W


DLC3
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Measure the resistance according to the value(s) in the table below.


    C188081E16


    Text in Illustration 
    *1
    DLC3
    -
    -

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    L - W*1
    G - W*2
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I39-6 (CANH) - I39-4 (CG)
    L - W-B*1
    G - W-B*2
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-6 (CANH) - I39-16 (BAT)
    L - R*1
    G - R*2
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    *1: for LHD
    *2: for RHD


POWER MANAGEMENT CONTROL ECU

C146689E49


Text in Illustration 
*a
Component without harness connected
(Power Management Control ECU)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. A204446E36
  3. Disconnect the power management control ECU connectors.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-25 (CA1H) - I4-24 (CA1L)
    G*1 - W
    BE*2 - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I4-25 (CA1H) - I4-4 (E12)
    G*1 - BR
    BE*2 - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I4-24 (CA1L) - I4-4 (E12)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I4-25 (CA1H) - I4-7 (AM21)
    G*1 - L
    BE*2 - L
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I4-24 (CA1L) - I4-7 (AM21)
    W - L
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:

    Sub Bus 15 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I4-31 (CA3P) - I4-30 (CA3N)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    I4-31 (CA3P) - I4-4 (E12)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I4-30 (CA3N) - I4-4 (E12)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I4-31 (CA3P) - I4-7 (AM21)
    B - L
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I4-30 (CA3N) - I4-7 (AM21)
    W - L
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


ECM

A262466E03


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the ECM connectors.


    C250518E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    A25-13 (CANH) - E28-16 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A25-26 (CANL) - E28-16 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A25-13 (CANH) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A25-26 (CANL) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


    Standard Resistance:

    Sub Bus 15 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-12 (CANP) - A25-25 (CANN)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    A25-12 (CANP) - E28-16 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A25-25 (CANN) - E28-16 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A25-12 (CANP) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A25-25 (CANN) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


COMBINATION METER ASSEMBLY

E224288E05


Text in Illustration 
*a
Component without harness connected
(Combination Meter Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. E224284E18
  3. Disconnect the combination meter assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-16 (CANH) - I18-15 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    I18-16 (CANH) - I18-7 (ES)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I18-15 (CANL) - I18-7 (ES)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I18-16 (CANH) - I18-1 (B)
    R - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I18-15 (CANL) - I18-1 (B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E09


Text in Illustration 
*A
for LHD
*B
for RHD
*a
Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the main body ECU (multiplex network body ECU) connectors.


    C250555E01


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I13-14 (CANH) - I13-13 (CANL)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I13-14 (CANH) - I39-4 (CG)
    P - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I13-13 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I13-14 (CANH) - I39-16 (BAT)
    P - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I13-13 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C156569E03


Text in Illustration 
*a
Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C249762E10
  3. Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (Brake Booster with Master Cylinder Assembly (Skid Control ECU))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A28-37 (CA1H) - A28-38 (CA1L)
    GR - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    A28-37 (CA1H) - A28-28 (GND)
    GR - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A28-38 (CA1L) - A28-28 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A28-37 (CA1H) - A28-15 (BS)
    GR - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A28-38 (CA1L) - A28-15 (BS)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


    Standard Resistance:

    Sub Bus 15 Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A28-35 (CA2H) - A28-34 (CA2L)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    A28-35 (CA2H) - A28-28 (GND)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A28-34 (CA2L) - A28-28 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A28-35 (CA2H) - A28-15 (BS)
    B - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A28-34 (CA2L) - A28-15 (BS)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


STEERING SENSOR
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C156493E63
  3. Disconnect the steering sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I30-3 (CANH) - I30-2 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I30-3 (CANH) - I30-1 (ESS)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I30-2 (CANL) - I30-1 (ESS)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I30-3 (CANH) - I30-5 (BAT)
    V - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I30-2 (CANL) - I30-5 (BAT)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


POWER STEERING ECU ASSEMBLY
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the power steering ECU assembly connectors.


    C239855E02


    Text in Illustration 
    *a
    Component without harness connected
    (Power Steering ECU Assembly)
    -
    -

    C250526E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j3-4 (CANH) - j3-8 (CANL)
    Y - SB
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    j3-4 (CANH) - j2-2 (PGND)
    Y - B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    j3-8 (CANL) - j2-2 (PGND)
    SB - B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    j3-4 (CANH) - j2-1 (PIG)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    j3-8 (CANL) - j2-1 (PIG)
    SB - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


AIRBAG SENSOR ASSEMBLY
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the airbag sensor assembly connector.


    C188802E20


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I47-13 (CANH) - I47-22 (CANL)
    Y - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I47-13 (CANH) - I47-25 (E1)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I47-22 (CANL) - I47-25 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I47-13 (CANH) - I39-16 (BAT)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I47-22 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)

C244122E01


Text in Illustration 
*a
Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the smart key ECU assembly (certification ECU) connector.


    C250527E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I87-1 (CANH) - I87-2 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I87-1 (CANH) - I86-1 (E)
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I87-2 (CANL) - I86-1 (E)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I87-1 (CANH) - I87-5 (+B)
    L - SB
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I87-2 (CANL) - I87-5 (+B)
    W - SB
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


RADIO AND DISPLAY RECEIVER ASSEMBLY

E225865E11


Text in Illustration 
*a
Component without harness connected
(Radio and Display Receiver Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the radio and display receiver assembly connectors.


    C240506E10


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I155-9 (CANH) - I155-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I155-9 (CANH) - I152-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I155-10 (CANL) - I152-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I155-9 (CANH) - I152-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I155-10 (CANL) - I152-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the air conditioning amplifier assembly connector.


    E226604E07


    Text in Illustration 
    *a
    Component without harness connected
    (Air Conditioning Amplifier Assembly)
    -
    -

    C188799E31


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I77-11 (CANH) - I77-12 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I77-11 (CANH) - I77-14 (GND)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I77-12 (CANL) - I77-14 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I77-11 (CANH) - I77-21 (B)
    V - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I77-12 (CANL) - I77-21 (B)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


CLEARANCE WARNING ECU ASSEMBLY (for RHD)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the clearance warning ECU assembly connector.


    C240483E03


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I82-17 (R1) - I82-18 (R2)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    I82-17 (R1) - I82-30 (E)
    P - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I82-18 (R2) - I82-30 (E)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I82-17 (R1) - I39-16 (BAT)
    P - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    I82-18 (R2) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher