CAN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CAN JUNCTION RH CONNECTOR (for LHD) |
Check the CAN junction RH connector.
Connection diagram

| *a | Component with harness connected (CAN Junction RH Connector) | *b | to Clearance Warning ECU Assembly (for V Bus) |
| *c | to ECM (for V Bus) | *d | to Air Conditioning Amplifier Assembly (for V Bus) |
| *e | to Airbag Sensor Assembly (for V Bus) | *f | to Smart Key ECU Assembly (Certification ECU) (for V Bus) |
| *g | to Power Steering ECU Assembly (for V Bus) | *h | to Radio and Display Receiver Assembly (for V Bus) |
| *i | to CAN Junction LH Connector (for V Bus) | - | - |
Check the connection diagram of the components which are connected to the CAN junction RH connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I111-1 (CANH) | BE | Clearance warning ECU assembly (for V bus) |
| I111-2 (CANL) | W | |
| I104-1 (CANH) | P | ECM (for V bus) |
| I104-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly (for V bus) |
| I102-2 (CANL) | W | |
| I99-1 (CANH) | Y | Airbag sensor assembly (for V bus) |
| I99-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (certification ECU) (for V bus) |
| I106-2 (CANL) | W | |
| I98-1 (CANH) | G | Power steering ECU assembly (for V bus) |
| I98-2 (CANL) | W | |
| I107-1 (CANH) | R | Radio and display receiver assembly (for V bus) |
| I107-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN junction LH connector (for V bus) |
| I101-2 (CANL) | W |
| CAN JUNCTION RH CONNECTOR (for RHD) |
Check the CAN junction RH connector.
Connection diagram

| *a | Component with harness connected (CAN Junction RH Connector) | *b | to Clearance Warning ECU Assembly (for V Bus) |
| *c | to Steering Sensor (for V Bus) | *d | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) (for V Bus) |
| *e | to Smart Key ECU Assembly (Certification ECU) (for V Bus) | *f | to DLC3 (for V Bus) |
| *g | to Combination Meter Assembly (for V Bus) | *h | to CAN Junction LH Connector (for V Bus) |
Check the connection diagram of the components which are connected to the CAN junction RH connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I111-1 (CANH) | P | Clearance warning ECU assembly (for V bus) |
| I111-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor (for V bus) |
| I97-2 (CANL) | W | |
| I110-1 (CANH) | Y | Brake booster with master cylinder assembly (skid control ECU) (for V bus) |
| I110-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (certification ECU) (for V bus) |
| I106-2 (CANL) | W | |
| I96-1 (CANH) | G | DLC3 (for V bus) |
| I96-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly (for V bus) |
| I94-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN junction LH connector (for V bus) |
| I101-2 (CANL) | W |
| CAN JUNCTION LH CONNECTOR (for LHD) |
Check the CAN junction LH connector.
Connection diagram

| *a | Component with harness connected (CAN Junction LH Connector) | *b | to Main Body ECU (Multiplex Network Body ECU) (for V Bus) |
| *c | to Steering Sensor (for V Bus) | *d | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) (for V Bus) |
| *e | to DLC3 (for V Bus) | *f | to Power Management Control ECU (for V Bus) |
| *g | to Combination Meter Assembly (for V Bus) | *h | to CAN Junction RH Connector (for V Bus) |
Check the connection diagram of the components which are connected to the CAN junction LH connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I95-1 (CANH) | P | Main body ECU (multiplex network body ECU) (for V bus) |
| I95-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor (for V bus) |
| I97-2 (CANL) | W | |
| I110-1 (CANH) | Y | Brake booster with master cylinder assembly (skid control ECU) (for V bus) |
| I110-2 (CANL) | W | |
| I96-1 (CANH) | L | DLC3 (for V bus) |
| I96-2 (CANL) | W | |
| I109-1 (CANH) | G | Power management control ECU (for V bus) |
| I109-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly (for V bus) |
| I94-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN junction RH connector (for V bus) |
| I93-2 (CANL) | W |
| CAN JUNCTION LH CONNECTOR (for RHD) |
Check the CAN junction LH connector.
Connection diagram

| *a | Component with harness connected (CAN Junction LH Connector) | *b | to Power Management Control ECU (for V Bus) |
| *c | to Main Body ECU (Multiplex Network Body ECU) (for V Bus) | *d | to Air Conditioning Amplifier Assembly (for V Bus) |
| *e | to Airbag Sensor Assembly (for V Bus) | *f | to Power Steering ECU Assembly (for V Bus) |
| *g | to ECM (for V Bus) | *h | to Radio and Display Receiver Assembly (for V Bus) |
| *i | to CAN Junction RH Connector (for V Bus) | - | - |
Check the connection diagram of the components which are connected to the CAN junction LH connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I109-1 (CANH) | BE | Power management control ECU (for V bus) |
| I109-2 (CANL) | W | |
| I95-1 (CANH) | P | Main body ECU (multiplex network body ECU) (for V bus) |
| I95-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly (for V bus) |
| I102-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly (for V bus) |
| I103-2 (CANL) | W | |
| I100-1 (CANH) | L | Power steering ECU assembly (for V bus) |
| I100-2 (CANL) | W | |
| I104-1 (CANH) | G | ECM (for V bus) |
| I104-2 (CANL) | W | |
| I107-1 (CANH) | R | Radio and display receiver assembly (for V bus) |
| I107-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN junction RH connector (for V bus) |
| I93-2 (CANL) | W |
| CAN NO. 1 JUNCTION CONNECTOR |
Check the CAN No. 1 junction connector.
Connection diagram

| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) | *b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) (for Sub Bus 15) |
| *c | to ECM (for Sub Bus 15) | *d | to Power Management Control ECU (for Sub Bus 15) |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| A72-1 (CANH) | B | Brake booster with master cylinder assembly (skid control ECU) (for Sub bus 15) |
| A72-7 (CANL) | W | |
| A72-2 (CANH) | B | ECM (for Sub bus 15) |
| A72-8 (CANL) | W | |
| A72-3 (CANH) | B | Power management control ECU (for Sub bus 15) |
| A72-9 (CANL) | W |
| DLC3 |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.

| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | L - W*1 G - W*2 | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I39-6 (CANH) - I39-4 (CG) | L - W-B*1 G - W-B*2 | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I39-6 (CANH) - I39-16 (BAT) | L - R*1 G - R*2 | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| POWER MANAGEMENT CONTROL ECU |

| *a | Component without harness connected (Power Management Control ECU) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the power management control ECU connectors.
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I4-25 (CA1H) - I4-24 (CA1L) | G - W*1 BE - W*2 | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I4-25 (CA1H) - I4-4 (E12) | G - BR*1 BE - BR*2 | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-24 (CA1L) - I4-4 (E12) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-25 (CA1H) - I4-7 (AM21) | G - L*1 BE - L*2 | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I4-24 (CA1L) - I4-7 (AM21) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I4-31 (CA3P) - I4-30 (CA3N) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I4-31 (CA3P) - I4-4 (E12) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-30 (CA3N) - I4-4 (E12) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-31 (CA3P) - I4-7 (AM21) | B - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I4-30 (CA3N) - I4-7 (AM21) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| ECM |

| *a | Component without harness connected (ECM) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the ECM connectors.

| *a | Front view of wire harness connector (to ECM) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A25-13 (CANH) - A25-26 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A25-13 (CANH) - E28-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-26 (CANL) - E28-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-13 (CANH) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A25-26 (CANL) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A25-12 (CANP) - A25-25 (CANN) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A25-12 (CANP) - E28-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-25 (CANN) - E28-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-12 (CANP) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A25-25 (CANN) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| COMBINATION METER ASSEMBLY |

| *a | Component without harness connected (Combination Meter Assembly) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I18-17 (CANH) - I18-16 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| I18-17 (CANH) - I18-20 (ES) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I18-16 (CANL) - I18-20 (ES) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I18-17 (CANH) - I18-1 (B) | R - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I18-16 (CANL) - I18-1 (B) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |

| *A | for LHD | *B | for RHD |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connectors.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I13-14 (CANH) - I13-13 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I13-14 (CANH) - I39-4 (CG) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I13-13 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I13-14 (CANH) - I39-16 (BAT) | P - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I13-13 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) |

| *a | Component without harness connected (Brake Booster with Master Cylinder Assembly (Skid Control ECU)) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A28-37 (CA1H) - A28-38 (CA1L) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A28-37 (CA1H) - A28-28 (GND) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-38 (CA1L) - A28-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-37 (CA1H) - A28-15 (BS) | GR - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A28-38 (CA1L) - A28-15 (BS) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A28-35 (CA2H) - A28-34 (CA2L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A28-35 (CA2H) - A28-28 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-34 (CA2L) - A28-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-35 (CA2H) - A28-15 (BS) | B - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A28-34 (CA2L) - A28-15 (BS) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| STEERING SENSOR |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the steering sensor connector.
| *a | Front view of wire harness connector (to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I30-3 (CANH) - I30-2 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I30-3 (CANH) - I30-1 (ESS) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I30-2 (CANL) - I30-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I30-3 (CANH) - I30-5 (BAT) | V - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I30-2 (CANL) - I30-5 (BAT) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| POWER STEERING ECU ASSEMBLY |

| *a | Component without harness connected (Power Steering ECU Assembly) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power steering ECU assembly connectors.

| *a | Front view of wire harness connector (to Power Steering ECU Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| j3-4 (CANH) - j3-8 (CANL) | Y - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| j3-4 (CANH) - j2-2 (PGND) | Y - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| j3-8 (CANL) - j2-2 (PGND) | SB - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| j3-4 (CANH) - j2-1 (PIG) | Y - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| j3-8 (CANL) - j2-1 (PIG) | SB - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| AIRBAG SENSOR ASSEMBLY |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the airbag sensor assembly connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I47-13 (CANH) - I47-22 (CANL) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I47-13 (CANH) - I47-25 (E1) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I47-22 (CANL) - I47-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I47-13 (CANH) - I39-16 (BAT) | Y - R | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I47-22 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) |

| *a | Component without harness connected (Smart Key ECU Assembly (Certification ECU)) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the smart key ECU assembly (certification ECU) connector.

| *a | Front view of wire harness connector (to Smart Key ECU Assembly (Certification ECU)) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I87-1 (CANH) - I87-2 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I87-1 (CANH) - I86-1 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I87-2 (CANL) - I86-1 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I87-1 (CANH) - I87-5 (+B) | L - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I87-2 (CANL) - I87-5 (+B) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| RADIO AND DISPLAY RECEIVER ASSEMBLY |

| *a | Component without harness connected (Radio and Display Receiver Assembly) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the radio and display receiver assembly connectors.

| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I155-9 (CANH) - I155-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I155-9 (CANH) - I152-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I155-10 (CANL) - I152-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I155-9 (CANH) - I152-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I155-10 (CANL) - I152-4 (+B1) | W - L-Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| AIR CONDITIONING AMPLIFIER ASSEMBLY |

| *a | Component without harness connected (Air Conditioning Amplifier Assembly) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the air conditioning amplifier assembly connector.

| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I77-11 (CANH) - I77-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I77-11 (CANH) - I77-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I77-12 (CANL) - I77-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I77-11 (CANH) - I77-21 (B) | V - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I77-12 (CANL) - I77-21 (B) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| CLEARANCE WARNING ECU ASSEMBLY |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the clearance warning ECU assembly connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Clearance Warning ECU Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I82-17 (R1) - I82-18 (R2) | BE - W*1 P - W*2 | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| I82-17 (R1) - I82-30 (E) | BE - BR*1 P - BR*2 | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I82-18 (R2) - I82-30 (E) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I82-17 (R1) - I39-16 (BAT) | BE - R*1 P - R*2 | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I82-18 (R2) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |