Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY

HOOD LOCK CONTROL CABLE ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



2. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



3. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure for the RH side and LH side .



4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:
Use the same procedure for the RH side and LH side .



5. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



6. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    B277166
  1. Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.



7. REMOVE FRONT BUMPER ASSEMBLY
(Click here)


8. REMOVE FRONT WHEEL LH (for LHD)


9. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for LHD)

HINT:
Use the same procedure for the RH side and LH side .



10. REMOVE FRONT FENDER LINER LH (for LHD)

HINT:
Use the same procedure for the RH side and LH side .



11. REMOVE FRONT WHEEL RH (for RHD)


12. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)


    E226631
  1. Remove the 3 screws and front wheel opening extension pad RH.



13. REMOVE FRONT FENDER LINER RH (for RHD)


    E231344
  1. Remove the clip.



    E226453E01
  1. Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.
    Text in Illustration 
    *a
    90°



    E226455E01
  1. Remove the 5 screws.
    Text in Illustration 
    *1
    Grommet

  1. Remove the 4 clips, 2 grommets and front fender liner RH.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



14. REMOVE HOOD LOCK ASSEMBLY (for LHD)


    B281661E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281667
  1. Disconnect the connector.



    B281671E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B281672
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



15. REMOVE HOOD LOCK ASSEMBLY (for RHD)


    B281669E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



    B281668
  1. Disconnect the connector.



    B281670E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B281673
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



16. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


  1. Using a screwdriver, disengage the 5 clamps and hood cable grommet as shown in the illustration.


    B291320E01


    Text in Illustration 
    *1
    Hood Lock Control Cable
    *2
    Hood Cable Grommet
    *3
    Washer Hose
    *4
    Hood Lock Control Cable Clamp

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the hood lock control cable assembly from the engine compartment and remove it.



17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


  1. Using a screwdriver, disengage the 4 clamps and hood cable grommet as shown in the illustration.


    B291321E01


    Text in Illustration 
    *1
    Hood Lock Control Cable
    *2
    Hood Cable Grommet
    *3
    Washer Hose
    *4
    Hood Lock Control Cable Clamp

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the hood lock control cable assembly from the engine compartment and remove it.