Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A60-288    Drive Motor "A" Phase V Current

DTC    P0A60-290    Drive Motor "A" Phase V Current

DTC    P0A60-294    Drive Motor "A" Phase V Current

DTC    P0A60-501    Drive Motor "A" Phase V Current

DTC    P0A63-296    Drive Motor "A" Phase W Current

DTC    P0A63-298    Drive Motor "A" Phase W Current

DTC    P0A63-302    Drive Motor "A" Phase W Current

DTC    P0A63-502    Drive Motor "A" Phase W Current

for Preparation Click here


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the motor inverter current sensors. P0A60 and P0A63 indicate malfunctions in current sensors, and they do not indicate malfunctions in the high-voltage system.

HINT:
The term "drive motor A" indicates MG2.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A60
288
Malfunction in motor inverter current sensor (phase V sub sensor)
Inverter with converter assembly
290
Malfunction in motor inverter current sensor (phase V main sensor)
294
Malfunction in motor inverter current sensor (performance problem or open phase V)
501
Malfunction in motor inverter current sensor (phase V main and sub sensors offset)
P0A63
296
Malfunction in motor inverter current sensor (phase W sub sensor)
298
Malfunction in motor inverter current sensor (phase W main sensor)
302
Malfunction in motor inverter current sensor (performance problem or open phase W)
502
Malfunction in motor inverter current sensor (phase W main and sub sensors offset)

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A60 or P0A63 only is output.
    A
    P0A78-202 is output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (P0A78-202) (Click here)
A


2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



  1. Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly (Click here).

    NOTICE:
    Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.


    A258444E01

    OK:
    The connectors are connected securely and there are no contact pressure problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)