Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P1C2D-587    Hybrid Battery Voltage / DC/DC Converter Voltage Correlation

for Preparation Click here


DESCRIPTION

For a description of the boost converter .
The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery smart unit to detect HV battery voltage (VB).

HINT:
Using the intelligent tester, check the Data List of Power Resource VB and Batt Pack Current Val. If these values are not within the below range, there is a battery smart unit malfunction.


A225448E03


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P1C2D
587
Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate
  1. Inverter with converter assembly
  2. Battery smart unit

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    DTC P1C2D-587 only is output. Alternatively, P1C2D- 587 and any DTCs other than P0B23-129, P0CA3-442 or P0E32-585 are output.
    A
    P1C2D-587 and P0B23-129 (HV battery voltage circuit malfunction) are output.
    B
    P1C2D-587 and P0CA3-442 (abnormal voltage execution value) are output.
    C
    P1C2D-587 and P0E32-585 (boost converter voltage (VL) sensor performance problem) are output.
    D

  1. Turn the power switch off.



B
GO TO DTC CHART (P0B23-129) (Click here)

C
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)

D
GO TO DTC CHART (P0E32-585) (Click here)
A


2.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3. (*1)

  1. Turn the power switch on (READY). (*2)

  1. Enter the following menus: Powertrain / Hybrid Control / Data List (*3)

  1. If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more. (*4)

  1. Move the shift lever to P. (*5)

  1. Set the air conditioning to MAX COOL and turn the headlights on. (*6)

  1. Confirm that "Batt Pack Current Val" is more than 3 A. (*7)

  1. Leave the vehicle for 15 seconds with the engine stopped during steps (*5) (*6) and (*7). (*8)

  1. Enter the following menus: Powertrain / Hybrid Control / DTC. (*9)

  1. Check if DTCs are output. (*10)

    NOTICE:
    If the low HV battery charge warning light comes on, Move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps (*1) through (*10) again.

    Result:
    Result
    Proceed to
    No DTCs are output, or DTCs other than the following are output.
    A
    P0B23-129 (HV battery voltage circuit malfunction) is output.
    B
    P0E32-585 (boost converter voltage (VL) sensor performance problem) is output.
    C
    P3000-388 (discharge inhibition) is output.
    D
    P3004-132 (high voltage power supply line problem) is output.
    E

  1. Turn the power switch off.



B
REPLACE BATTERY SMART UNIT (Click here)

C
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)

D
LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*1) THROUGH (*10))

E
REPLACE BATTERY SMART UNIT (Click here)
A


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Turn the power switch on (READY). (*11)

  1. Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. (*12)

  1. Connect the intelligent tester to the DLC3. (*13)

  1. Enter the following menus: Powertrain / Hybrid Control / DTC. (*14)

  1. Check if DTCs are output. (*15)

    Result:
    Result
    Proceed to
    No DTCs are output, or DTCs other than the following are output.
    A
    P0B23-129 (HV battery voltage circuit malfunction) is output.
    B
    P0E32-585 (boost converter voltage (VL) sensor performance problem) is output.
    C
    P3000-388 (discharge inhibition) is output.
    D
    P3004-132 (high voltage power supply line problem) is output.
    E

  1. Turn the power switch off.



B
REPLACE BATTERY SMART UNIT (Click here)

C
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)

D
LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*11) THROUGH (*15))

E
REPLACE BATTERY SMART UNIT (Click here)
A


5.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List.

  1. Select "Power Resource VB", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" in the Data List.

  1. If both "Power Resource VB" and VL-Voltage before Boosting are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more.

  1. Move the shift lever to P (the engine is off), and read the Data List when the vehicle is stationary.

    Result:

    Result
    Proceed to
    Both of the following are not satisfied.
    A
    Both of the following are satisfied:
    1. Difference between "Power Resource VB" and "VH-Voltage after Boosting" is less than 5 V.
    2. Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V.
    B
    Both of the following are satisfied:
    1. Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is more than 5 V.
    2. Difference between "Power Resource VB" and "VH-Voltage after Boosting" is less than 15 V.
    C

  1. Turn the power switch off.



B
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)

C
REPLACE BATTERY SMART UNIT (Click here)
A


6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read the freeze frame data of DTC P0A94-587.

    Result:

    Result
    Proceed to
    Both of the following are satisfied or both of the following are not satisfied.
    A
    "Power Resource VB" is less than 190 V or more than 340 V.
    B
    "VL-Voltage before Boosting" is less than 190 V or more than 340 V.
    C

  1. Turn the power switch off.



B
REPLACE BATTERY SMART UNIT (Click here)

C
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)
A


7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read the freeze frame data of DTC P0A94-587.

    HINT:
    In the freeze frame data, read the "Power Resource VB" and all of the "Battery Block Vol".


    Result:

    Result
    Proceed to
    Others (Freeze frame data is not stored).
    A
    Both of the following are satisfied:
    1. Sum of all "Battery Block Vol" is more than ("Power Resource VB" - 45 V)
    2. Sum of all "Battery Block Vol" is less than ("Power Resource VB" + 30 V)
    B
    Neither A nor B is satisfied.
    C

  1. Turn the power switch off.



B
REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)

C
REPLACE BATTERY SMART UNIT (Click here)
A


8.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List.

  1. If both "Battery Block Vol" and "VL-Voltage before Boosting" are less than 280 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 280 V or more.

  1. Move the shift lever to P (the engine is off), and read the "Power Resource VB" and all of the "Battery Block Vol", when the vehicle is stationary.

    Result:

    Result
    Proceed to
    Both of the following are satisfied:
    1. Sum of all "Battery Block Vol" is more than ("Power Resource VB" -45 V)
    2. Sum of all "Battery Block Vol" is less than ("Power Resource VB" +30 V)
    A
    The preceding condition is not satisfied.
    B

  1. Turn the power switch off.



B
REPLACE BATTERY SMART UNIT (Click here)
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)