ENGINE ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM |
Turn the power switch on (READY).
Turn the A/C switch on.
Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.
Turn the power switch off.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 5. REMOVE BAGGAGE HOLDER NET (w/ Partition Net) |
Remove the baggage holder net.
| 6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT |
Remove the luggage compartment floor mat.
| 7. REMOVE LUGGAGE COMPARTMENT TRIM COVER FRONT |
![]() |
Disengage the 8 fasteners.
Disengage the 2 claws and remove the luggage compartment front trim cover.
| 8. REMOVE NO. 8 HYBRID VEHICLE BATTERY SHIELD PANEL |
![]() |
Remove the 2 nuts and No. 8 hybrid vehicle battery shield panel.
| 9. REMOVE SERVICE PLUG GRIP |
Wear insulating gloves and remove the service plug grip after sliding up the lever of the service plug grip as shown in the illustration.

| 10. DISCHARGE FUEL SYSTEM PRESSURE |
| 11. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD |
| 12. SECURE STEERING WHEEL |
![]() |
Secure the steering wheel with the seat belt in order to prevent rotation.
| 13. REMOVE FRONT WHEELS |
| 14. REMOVE FRONT BUMPER ABSORBER LOWER |
| 15. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 16. REMOVE ENGINE UNDER COVER LH |
| 17. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 18. REMOVE ENGINE UNDER COVER RH |
| 19. REMOVE FRONT FENDER APRON SEAL LH |
| 20. REMOVE FRONT FENDER APRON SEAL RH |
| 21. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Clean the oil pan drain plug and install a new gasket and the oil pan drain plug.
| 22. DRAIN COOLANT (for Engine) |
Loosen the radiator drain cock plug.
Remove the radiator cap sub-assembly.

| *1 | Radiator Cap Sub-assembly | *2 | Radiator Drain Cock Plug |
| 23. DRAIN COOLANT (for Inverter) |
Remove the reserve tank cap.
![]() |
Using a hexagon wrench (10 mm), remove the drain plug indicated in the illustration and drain the coolant.
Install the plug with a new gasket.
| 24. DRAIN HYBRID TRANSMISSION FLUID |
![]() |
Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
| *1 | Filler Plug |
| *2 | Drain Plug |
Using a 10 mm hexagon socket wrench, remove the drain plug and gasket to drain the hybrid transaxle fluid.
Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket.
| 25. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the No. 1 engine cover sub-assembly.
| 26. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 9 clips and cool air intake duct seal.
| 27. REMOVE CONNECTOR COVER ASSEMBLY |
![]() |
Remove the 2 bolts and connector cover assembly.
| 28. CHECK TERMINAL VOLTAGE |
![]() |
Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.
| 29. TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY |
![]() |
Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.
| 30. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 31. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.
Disconnect the ventilation hose from the cylinder head cover.
Disconnect the connector.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
![]() |
Disconnect the 2 fuel vapor feed hoses.
| *1 | Retainer |
| *2 | Fuel Tube Connector |
| *3 | Pipe |
| *4 | O-ring |
| *a | Pull |
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
| 32. REMOVE AIR CLEANER FILTER ELEMENT |
| 33. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and air cleaner case sub-assembly.
| *a | Projection |
| 34. REMOVE NO. 5 INVERTER BRACKET |
![]() |
Remove the 2 bolts and No. 5 inverter bracket.
| 35. REMOVE NO. 4 INVERTER BRACKET |
![]() |
Remove the 3 bolts and No. 4 inverter bracket.
| 36. REMOVE UPPER INVERTER COVER |
![]() |
Remove the 2 bolts and upper inverter cover (generator cable side).
| 37. DISCONNECT GENERATOR CABLE |
![]() |
Using an insulated tool, remove the 3 bolts.
![]() |
Disconnect the 2 wire harness clamps and separate the generator cable.
| 38. REMOVE UPPER INVERTER COVER |
![]() |
Remove the 2 bolts and upper inverter cover (motor cable side).
| 39. DISCONNECT MOTOR CABLE |
![]() |
Using an insulated tool, remove the 3 bolts.
![]() |
Disconnect the 3 wire harness clamps and separate the motor cable.
| 40. REMOVE NO. 3 MOTOR CABLE BRACKET |
![]() |
Disconnect the hose clamp from the No. 3 motor cable bracket.
Remove the 2 bolts and No. 3 motor cable bracket.
| 41. REMOVE CONNECTOR COVER ASSEMBLY |
![]() |
Remove the bolt and connector cover assembly.
| 42. DISCONNECT NO. 4 ENGINE WIRE |
![]() |
Disconnect the No. 4 engine wire.
![]() |
Disconnect the wire harness clamp.
| 43. REMOVE NO. 4 FLOOR WIRE |
![]() |
Remove the bolt.
![]() |
Disconnect the wire harness clamp and connector.
| 44. TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY |
![]() |
Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.
| 45. DISCONNECT LOW VOLTAGE CONNECTOR |
![]() |
Raise the lock lever and disconnect the 3 low voltage connectors.
Disconnect the low voltage connector from the inverter with converter assembly.
| 46. DISCONNECT NO. 3 ENGINE ROOM WIRE |
Remove the relay block cover.
![]() |
Remove the nut.
Disconnect the wire harness clamp and No. 3 engine room wire.
| 47. REMOVE NO. 4 INVERTER COOLING HOSE |
![]() |
Release the retainer and disconnect the No. 4 inverter cooling hose from the inverter with converter assembly.
| *1 | Retainer |
![]() |
Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.
| 48. REMOVE NO. 1 INVERTER COOLING HOSE ASSEMBLY |
![]() |
Release the retainer and disconnect the No. 1 inverter cooling hose from the inverter with converter assembly.
| *1 | Retainer |
![]() |
Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.
| 49. REMOVE INVERTER WITH CONVERTER ASSEMBLY |
![]() |
Temporarily secure the No. 3 engine room wire with the inverter with converter assembly hook as shown in the illustration.
| *1 | No. 3 Engine Room Wire |
| *2 | Hook |
![]() |
Remove the 2 bolts, nut and inverter with converter assembly.
![]() |
Even after the coolant is drained, coolant remains in the inverter with converter assembly due to its internal structure. Therefore, seal or cover the pipes when removing the inverter with converter to prevent coolant from spilling out or foreign matter from entering the inverter with converter.
| 50. DISCONNECT NO. 4 ENGINE WIRE |
![]() |
Remove the 3 wire harness clamps and disconnect the No. 4 engine wire from the fan shroud.
| 51. DISCONNECT ENGINE WIRE |
![]() |
Disconnect the 4 connectors and disconnect the wire harness clamp.
![]() |
Remove the bolt and disconnect the earth wire from the body.
![]() |
Pull up the lever to disconnect the ECM connector.
Disconnect the wire clamp.
| 52. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.
Remove the clip from the transmission control cable assembly.
![]() |
Disconnect the transmission control cable assembly from the 2 transmission control brackets.
| 53. DISCONNECT NO. 1 RADIATOR HOSE |
![]() |
Remove the hose clamp to disconnect the air fuel ratio sensor wire from the No. 1 radiator hose.
Disconnect the No. 1 radiator hose.
| 54. DISCONNECT NO. 5 INVERTER COOLING HOSE |
![]() |
Disconnect the No. 5 inverter cooling hose from the hybrid vehicle transaxle assembly.
| 55. DISCONNECT INLET HEATER WATER HOSE |
![]() |
Disconnect the inlet heater water hose.
| 56. DISCONNECT OUTLET HEATER WATER HOSE |
![]() |
Disconnect the outlet heater water hose.
| 57. DISCONNECT FUEL MAIN TUBE |
![]() |
Release the claw and remove the No. 1 EFI fuel pipe clamp.
![]() |
Pinch the fuel tube connector and then pull out the fuel main tube.
| 58. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Remove the 2 bolts and No. 2 engine mounting stay RH.
| 59. SEPARATE EARTH WIRE |
![]() |
Remove the bolt and separate the earth wire from the engine moving control rod bracket.
| 60. REMOVE ENGINE MOVING CONTROL ROD BRACKET |
![]() |
Remove the 4 bolts and engine moving control rod bracket.
| 61. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the bolt and engine moving control rod from the engine moving control rod bracket.
| 62. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose from the compressor with motor assembly.
Remove the O-ring from the No. 1 cooler refrigerant suction hose.
| 63. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor with motor assembly.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
| 64. DISCONNECT NO. 2 RADIATOR HOSE |
![]() |
Disconnect the No. 2 radiator hose.
| 65. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Remove the front exhaust pipe assembly from the exhaust pipe support.
Remove the gasket from the exhaust manifold converter sub-assembly.
| 66. DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the steering intermediate shaft assembly and steering link assembly.
| *a | Matchmark |
Remove the bolt.
Separate the steering intermediate shaft assembly from the steering link assembly.
| 67. REMOVE FRONT AXLE SHAFT NUT LH |
![]() |
Using SST and a hammer, release the staked part of the front axle shaft nut.
While applying the brakes, remove the front axle shaft nut.
| 68. REMOVE FRONT AXLE HUB NUT RH |
| 69. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
If the ball joint turns together with the nut, use a wrench to hold the stud bolt.
| 70. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 71. SEPARATE FRONT SPEED SENSOR LH |
![]() |
Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.
![]() |
Remove the bolt and front speed sensor from the steering knuckle.
| 72. SEPARATE FRONT SPEED SENSOR RH |
| 73. SEPARATE TIE ROD ASSEMBLY LH |
![]() |
Remove the cotter pin and nut.
![]() |
Install SST to the tie rod assembly LH.
Secure SST using a string.
Using SST, separate the tie rod assembly LH from the steering knuckle.

| *1 | Center Nut | - | - |
| *a | String | *b | Grease Application Area |
![]() | Place the wrench here. | - | - |
| 74. SEPARATE TIE ROD ASSEMBLY RH |
| 75. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.
| 76. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH |
| 77. SEPARATE FRONT AXLE ASSEMBLY LH |
![]() |
Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
| *a | Matchmark |
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.
| 78. SEPARATE FRONT AXLE ASSEMBLY RH |
| 79. REMOVE FLYWHEEL HOUSING UNDER COVER |
![]() |
Remove the flywheel housing under cover.
| 80. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
![]() |
Set an engine lifter.
![]() | Attachment Installation Position |
![]() |
| *1 | No. 2 Motor Water Jacket Cover Assembly |
![]() |
Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.
| *1 | Nut |
Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.
Operate the engine lifter and remove the engine assembly from the vehicle.
Install the engine hangers .
| 81. REMOVE ENGINE WIRE |
Remove the engine wire from the engine with transaxle.
| 82. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the front drive shaft assembly LH.
| 83. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH |
![]() |
Using a screwdriver, remove the front drive shaft hole snap ring LH.
| 84. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.
| 85. REMOVE FRONT FRAME ASSEMBLY |
![]() |
Remove the bolt and disconnect the No. 4 engine wire from the front frame assembly.
![]() |
Remove the nut and separate the engine mounting insulator LH.
![]() |
Remove the bolt and separate the front engine mounting insulator.
![]() |
Remove the nut and separate the engine mounting insulator RH.
Remove the front frame assembly.
Using a height adjustable attachment and plate lift attachment, place the engine assembly on a flat level surface.
| 86. REMOVE FRONT ENGINE MOUNTING INSULATOR |
![]() |
Remove the 3 nuts and front engine mounting insulator.
| 87. REMOVE ENGINE MOUNTING INSULATOR LH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator LH.
| 88. REMOVE ENGINE MOUNTING INSULATOR RH |
![]() |
Remove the 2 hole plugs from the front frame assembly.
Remove the 3 nuts and engine mounting insulator RH.
| 89. REMOVE ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 3 bolts and engine mounting bracket RH.
| 90. REMOVE DRIVE SHAFT BEARING BRACKET |
![]() |
Remove the 3 bolts and drive shaft bearing bracket.
| 91. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY |
Using the transmission jack attachment, set the hybrid vehicle transaxle assembly on a transmission jack.
![]() |
Remove the 9 bolts and hybrid vehicle transaxle assembly.
| 92. REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 6 bolts and transmission input damper assembly.
| 93. REMOVE FLYWHEEL SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft pulley.
![]() |
Remove the 8 bolts and flywheel sub-assembly.
| 94. INSTALL ENGINE STAND |
Install the engine onto an engine stand with the bolts.