Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
  1. The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
  2. The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution (Click here).

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the power switch on (READY).

  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the power switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)
  1. Remove the baggage holder net.



6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT
  1. Remove the luggage compartment floor mat.



7. REMOVE LUGGAGE COMPARTMENT TRIM COVER FRONT


    B287041
  1. Disengage the 8 fasteners.

  1. Disengage the 2 claws and remove the luggage compartment front trim cover.



8. REMOVE NO. 8 HYBRID VEHICLE BATTERY SHIELD PANEL


    A258773
  1. Remove the 2 nuts and No. 8 hybrid vehicle battery shield panel.



9. REMOVE SERVICE PLUG GRIP

CAUTION:
  1. Wear insulating gloves.
  2. Remove the service plug grip to interrupt the high voltage circuit at the time of inspection or repair.
  3. Keep the removed service plug grip in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
  4. All the high voltage wiring connectors are orange.



  1. Wear insulating gloves and remove the service plug grip after sliding up the lever of the service plug grip as shown in the illustration.


    A258774

    CAUTION:
    1. Keep the removed service plug grip in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
    2. After removing the service plug grip, do not touch the high voltage connectors or terminals for 10 minutes.

    HINT:
    Waiting for at least 10 minutes is required to discharge the high voltage capacitor inside the inverter with converter assembly.



10. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


11. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


12. SECURE STEERING WHEEL


    C238510
  1. Secure the steering wheel with the seat belt in order to prevent rotation.

    HINT:
    This operation is useful to prevent damage to the spiral cable.



13. REMOVE FRONT WHEELS


14. REMOVE FRONT BUMPER ABSORBER LOWER


15. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


16. REMOVE ENGINE UNDER COVER LH


17. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH


18. REMOVE ENGINE UNDER COVER RH


19. REMOVE FRONT FENDER APRON SEAL LH


20. REMOVE FRONT FENDER APRON SEAL RH


21. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Clean the oil pan drain plug and install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



22. DRAIN COOLANT (for Engine)

NOTICE:
Do not remove the radiator cap sub-assembly or radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.



  1. Remove the radiator cap sub-assembly.


    A259346E01


    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Drain Cock Plug

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



23. DRAIN COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign objects.
  2. Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.

  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A258732
  1. Using a hexagon wrench (10 mm), remove the drain plug indicated in the illustration and drain the coolant.

    CAUTION:
    Use caution when handling coolant immediately after driving or in summer because it may be hot.

  1. Install the plug with a new gasket.

    Torque:
    39 N*m{ 397 kgf*cm , 29 ft.*lbf }



24. DRAIN HYBRID TRANSMISSION FLUID


    C243608E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug
    *2
    Drain Plug

  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket to drain the hybrid transaxle fluid.

  1. Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



25. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A259744
  1. Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the No. 1 engine cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



26. REMOVE COOL AIR INTAKE DUCT SEAL


    B287250
  1. Remove the 9 clips and cool air intake duct seal.



27. REMOVE CONNECTOR COVER ASSEMBLY

CAUTION:
  1. Do not touch the high voltage connectors and terminals for 10 minutes after the service plug grip is removed.
  2. Wear insulated gloves.

NOTICE:
Do not start the hybrid system with the service plug grip removed because it may cause a malfunction.



    A258734
  1. Remove the 2 bolts and connector cover assembly.

    NOTICE:
    1. Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the cover.
    2. Do not allow any foreign objects or water to enter the inverter with converter assembly.



28. CHECK TERMINAL VOLTAGE

CAUTION:
Wear insulated gloves.

NOTICE:
Do not allow any foreign objects or water to enter the inverter with converter assembly.



    A258735
  1. Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

    Standard voltage:
    0 V

    HINT:
    Use a measuring range of DC 750 V or more on the voltmeter.



29. TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:
Wear insulated gloves.



    A258736
  1. Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.



30. REMOVE INLET AIR CLEANER ASSEMBLY


    A259747
  1. Remove the 2 bolts and inlet air cleaner assembly.



31. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A259032
  1. Disconnect the mass air flow meter connector and wire harness clamp from the air cleaner cap sub-assembly.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the connector.



    A259031
  1. Release the 2 clamps and remove the air cleaner cap sub-assembly.



    A259684E01
  1. Disconnect the 2 fuel vapor feed hoses.
    Text in Illustration 
    *1
    Retainer
    *2
    Fuel Tube Connector
    *3
    Pipe
    *4
    O-ring
    *a
    Pull

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel vapor feed hose.



    A259033
  1. Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.



32. REMOVE AIR CLEANER FILTER ELEMENT


33. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A259768E03
  1. Remove the 2 bolts and air cleaner case sub-assembly.
    Text in Illustration 
    *a
    Projection



34. REMOVE NO. 5 INVERTER BRACKET


    A258737
  1. Remove the 2 bolts and No. 5 inverter bracket.



35. REMOVE NO. 4 INVERTER BRACKET


    A258738
  1. Remove the 3 bolts and No. 4 inverter bracket.



36. REMOVE UPPER INVERTER COVER

CAUTION:
Wear insulated gloves.



    A258739
  1. Remove the 2 bolts and upper inverter cover (generator cable side).

    NOTICE:
    1. Make sure to pull the upper inverter cover straight up, as a connector is connected to the bottom of the cover.
    2. Do not touch the upper inverter cover waterproofing rubber.



37. DISCONNECT GENERATOR CABLE

CAUTION:
Wear insulated gloves.



    A258740
  1. Using an insulated tool, remove the 3 bolts.



    A258741
  1. Disconnect the 2 wire harness clamps and separate the generator cable.

    NOTICE:
    1. Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.
    2. Do not touch the connector waterproofing rubber or terminals.
    3. Insulate the removed terminals with insulating tape.
    4. Do not allow any foreign objects or water to enter the inverter with converter assembly.



38. REMOVE UPPER INVERTER COVER

CAUTION:
Wear insulated gloves.



    A258742
  1. Remove the 2 bolts and upper inverter cover (motor cable side).

    NOTICE:
    1. Make sure to pull the upper inverter cover straight up, as a connector is connected to the bottom of the cover.
    2. Do not touch the upper inverter cover waterproofing rubber.



39. DISCONNECT MOTOR CABLE

CAUTION:
Wear insulated gloves.



    A258743
  1. Using an insulated tool, remove the 3 bolts.



    A258744
  1. Disconnect the 3 wire harness clamps and separate the motor cable.

    NOTICE:
    1. Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.
    2. Do not touch the connector waterproofing rubber or terminals.
    3. Insulate the removed terminals with insulating tape.
    4. Do not allow any foreign objects or water to enter the inverter with converter assembly.



40. REMOVE NO. 3 MOTOR CABLE BRACKET


    A258748
  1. Disconnect the hose clamp from the No. 3 motor cable bracket.

    HINT:
    Do not remove the hose clamp from the hose.

  1. Remove the 2 bolts and No. 3 motor cable bracket.



41. REMOVE CONNECTOR COVER ASSEMBLY

CAUTION:
Wear insulated gloves.



    A258751
  1. Remove the bolt and connector cover assembly.

    NOTICE:
    1. Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the cover.
    2. Do not allow any foreign objects or water to enter the inverter with converter assembly.



42. DISCONNECT NO. 4 ENGINE WIRE

CAUTION:
Wear insulated gloves.



    A258749
  1. Disconnect the No. 4 engine wire.

    NOTICE:
    1. Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.
    2. Do not touch the connector waterproofing rubber or terminals.
    3. Insulate the removed terminals with insulating tape.
    4. Do not allow any foreign objects or water to enter the inverter with converter assembly.



    A258750
  1. Disconnect the wire harness clamp.



43. REMOVE NO. 4 FLOOR WIRE


    A258752
  1. Remove the bolt.



    A258753
  1. Disconnect the wire harness clamp and connector.

    NOTICE:
    1. Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.
    2. Do not touch the connector waterproofing rubber or terminals.
    3. Insulate the removed terminals with insulating tape.
    4. Do not allow any foreign objects or water to enter the inverter with converter assembly.



44. TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:
Wear insulated gloves.



    A258736
  1. Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.



45. DISCONNECT LOW VOLTAGE CONNECTOR

NOTICE:
  1. Insulate the removed terminals with insulating tape.
  2. Do not allow any foreign objects or water to enter the inverter with converter assembly.



    A258754
  1. Raise the lock lever and disconnect the 3 low voltage connectors.

  1. Disconnect the low voltage connector from the inverter with converter assembly.



46. DISCONNECT NO. 3 ENGINE ROOM WIRE
  1. Remove the relay block cover.



    A258761
  1. Remove the nut.

  1. Disconnect the wire harness clamp and No. 3 engine room wire.



47. REMOVE NO. 4 INVERTER COOLING HOSE


    A258758E01
  1. Release the retainer and disconnect the No. 4 inverter cooling hose from the inverter with converter assembly.
    Text in Illustration 
    *1
    Retainer



    A260009
  1. Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.



48. REMOVE NO. 1 INVERTER COOLING HOSE ASSEMBLY


    A258759E01
  1. Release the retainer and disconnect the No. 1 inverter cooling hose from the inverter with converter assembly.
    Text in Illustration 
    *1
    Retainer



    A260010
  1. Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.



49. REMOVE INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Wear insulated gloves.



    A258762E01
  1. Temporarily secure the No. 3 engine room wire with the inverter with converter assembly hook as shown in the illustration.
    Text in Illustration 
    *1
    No. 3 Engine Room Wire
    *2
    Hook



    A258760
  1. Remove the 2 bolts, nut and inverter with converter assembly.

    NOTICE:
    1. Since the inverter with converter assembly is very heavy, 2 people are needed to remove the inverter with converter assembly. When removing the inverter with converter assembly, do not damage the parts around it.
    2. To prevent damage, do not hold the inverter with converter assembly by the connectors.
    3. To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.



    A148374
  1. Even after the coolant is drained, coolant remains in the inverter with converter assembly due to its internal structure. Therefore, seal or cover the pipes when removing the inverter with converter to prevent coolant from spilling out or foreign matter from entering the inverter with converter.



50. DISCONNECT NO. 4 ENGINE WIRE


    A259745
  1. Remove the 3 wire harness clamps and disconnect the No. 4 engine wire from the fan shroud.



51. DISCONNECT ENGINE WIRE


    A259755
  1. Disconnect the 4 connectors and disconnect the wire harness clamp.



    A259753
  1. Remove the bolt and disconnect the earth wire from the body.



    A259754
  1. Pull up the lever to disconnect the ECM connector.

  1. Disconnect the wire clamp.



52. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    A268022
  1. Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.

  1. Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with clip from the No. 1 transmission control cable bracket.

  1. Remove the clip from the transmission control cable assembly.



    C243612
  1. Disconnect the transmission control cable assembly from the 2 transmission control brackets.



53. DISCONNECT NO. 1 RADIATOR HOSE


    A259752
  1. Remove the hose clamp to disconnect the air fuel ratio sensor wire from the No. 1 radiator hose.

  1. Disconnect the No. 1 radiator hose.



54. DISCONNECT NO. 5 INVERTER COOLING HOSE


    A259746
  1. Disconnect the No. 5 inverter cooling hose from the hybrid vehicle transaxle assembly.



55. DISCONNECT INLET HEATER WATER HOSE


    A260220
  1. Disconnect the inlet heater water hose.



56. DISCONNECT OUTLET HEATER WATER HOSE


    A260221
  1. Disconnect the outlet heater water hose.



57. DISCONNECT FUEL MAIN TUBE


    A203577
  1. Release the claw and remove the No. 1 EFI fuel pipe clamp.



    A167796
  1. Pinch the fuel tube connector and then pull out the fuel main tube.

    NOTICE:
    1. Check for dirt and foreign objects on the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



58. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A259961
  1. Remove the 2 bolts and No. 2 engine mounting stay RH.



59. SEPARATE EARTH WIRE


    A259960
  1. Remove the bolt and separate the earth wire from the engine moving control rod bracket.



60. REMOVE ENGINE MOVING CONTROL ROD BRACKET


    A259959
  1. Remove the 4 bolts and engine moving control rod bracket.



61. REMOVE ENGINE MOVING CONTROL ROD


    A255850
  1. Remove the bolt and engine moving control rod from the engine moving control rod bracket.

    HINT:
    Perform this procedure only when replacement of the engine moving control rod is necessary.



62. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE


    E230575
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant suction hose from the compressor with motor assembly.

  1. Remove the O-ring from the No. 1 cooler refrigerant suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



63. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E230574
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor with motor assembly.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



64. DISCONNECT NO. 2 RADIATOR HOSE


    A260222
  1. Disconnect the No. 2 radiator hose.



65. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A258964
  1. Remove the 2 bolts and 2 compression springs.

  1. Remove the front exhaust pipe assembly from the exhaust pipe support.

  1. Remove the gasket from the exhaust manifold converter sub-assembly.



66. DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    C238511E02
  1. Put matchmarks on the steering intermediate shaft assembly and steering link assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt.

  1. Separate the steering intermediate shaft assembly from the steering link assembly.



67. REMOVE FRONT AXLE SHAFT NUT LH


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle shaft nut.



68. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedure described for the LH side.



69. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C238963
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
    If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



70. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



71. SEPARATE FRONT SPEED SENSOR LH


    C238961
  1. Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.

    NOTICE:
    Be sure to separate the front speed sensor from the front shock absorber assembly completely.



    C238448
  1. Remove the bolt and front speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from contacting the sensor tip.
    2. Be careful not to damage the front speed sensor.
    3. Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.



72. SEPARATE FRONT SPEED SENSOR RH

HINT:
Use the same procedure described for the LH side.



73. SEPARATE TIE ROD ASSEMBLY LH


    C238512
  1. Remove the cotter pin and nut.



    C238513E01
  1. Install SST to the tie rod assembly LH.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the lower ends of the tie rod assembly LH and SST are aligned.

  1. Secure SST using a string.

    NOTICE:
    Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



  1. Using SST, separate the tie rod assembly LH from the steering knuckle.


    C238514E02


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Grease Application Area
    V100136
    Place the wrench here.
    -
    -
    SST
    09960-20010   (09961-02010)

    CAUTION:
    Apply grease to the bolt threads and the tip of SST.

    NOTICE:
    1. Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



74. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



75. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    C238969
  1. Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.



76. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



77. SEPARATE FRONT AXLE ASSEMBLY LH


    C238968E01
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
    If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.



78. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



79. REMOVE FLYWHEEL HOUSING UNDER COVER


    A259962
  1. Remove the flywheel housing under cover.



80. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE


    A260219
  1. Set an engine lifter.
    Text in Illustration 
    V100145
    Attachment Installation Position

    NOTICE:
    1. Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.
    2. Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.
    3. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
    4. Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.
    5. Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed or removed from an engine stand.

    6. A346911E01
      To prevent coolant leaks, do not position the height adjustment attachments or plate lift attachments under the No. 2 motor water jacket cover assembly.
      Text in Illustration 
      *1
      No. 2 Motor Water Jacket Cover Assembly



    A260218E03
  1. Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.
    Text in Illustration 
    *1
    Nut

  1. Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.

  1. Operate the engine lifter and remove the engine assembly from the vehicle.

    NOTICE:
    1. Make sure that the engine is clear of all wiring and hoses.
    2. While lowering the engine from the vehicle, do not allow it to contact the vehicle.

  1. Install the engine hangers .



81. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine with transaxle.



82. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C239400E01
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-00031  
    09520-01010  

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly LH.



83. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    C057543
  1. Using a screwdriver, remove the front drive shaft hole snap ring LH.



84. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C239409
  1. Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly RH.

  1. Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.



85. REMOVE FRONT FRAME ASSEMBLY


    A259957
  1. Remove the bolt and disconnect the No. 4 engine wire from the front frame assembly.



    A255456
  1. Remove the nut and separate the engine mounting insulator LH.



    A260223
  1. Remove the bolt and separate the front engine mounting insulator.



    A255455
  1. Remove the nut and separate the engine mounting insulator RH.

  1. Remove the front frame assembly.

  1. Using a height adjustable attachment and plate lift attachment, place the engine assembly on a flat level surface.

    NOTICE:
    1. Using a height adjustable attachment and plate lift attachment, place the engine assembly with transaxle horizontally.
    2. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
    3. Using an engine sling device and engine lift, secure the engine assembly before service.



86. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A259963
  1. Remove the 3 nuts and front engine mounting insulator.

    HINT:
    Perform this procedure only when replacement of the front engine mounting insulator is necessary.



87. REMOVE ENGINE MOUNTING INSULATOR LH


    A255459
  1. Remove the 2 hole plugs from the front frame assembly.

  1. Remove the 3 nuts and engine mounting insulator LH.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



88. REMOVE ENGINE MOUNTING INSULATOR RH


    A255460
  1. Remove the 2 hole plugs from the front frame assembly.

  1. Remove the 3 nuts and engine mounting insulator RH.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



89. REMOVE ENGINE MOUNTING BRACKET RH


    A196634
  1. Remove the 3 bolts and engine mounting bracket RH.



90. REMOVE DRIVE SHAFT BEARING BRACKET


    A196633
  1. Remove the 3 bolts and drive shaft bearing bracket.



91. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY
  1. Using the transmission jack attachment, set the hybrid vehicle transaxle assembly on a transmission jack.

    NOTICE:
    1. Secure the hybrid vehicle transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
    2. To prevent the motor water jacket cover assembly from deforming, do not place any attachments onto the motor water jacket cover assembly of the hybrid vehicle transaxle assembly.
    3. Hold the engine assembly with a suitable adapter, such as a rope, during the operation.



    C243594
  1. Remove the 9 bolts and hybrid vehicle transaxle assembly.

    NOTICE:
    1. To avoid damage to the knock pins, do not pry between the hybrid vehicle transaxle assembly and the engine.
    2. To prevent the splines of the damper from becoming misaligned, do not allow the transaxle to hit the damper during transaxle removal and installation.



92. REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY


    A195875E06
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015  
    09330-00021  

    HINT:
    SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650 (2 pcs)



    A260502
  1. Remove the 6 bolts and transmission input damper assembly.



93. REMOVE FLYWHEEL SUB-ASSEMBLY


    A195875E06
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-54015  
    09330-00021  

    HINT:
    SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650 (2 pcs)



    A259955
  1. Remove the 8 bolts and flywheel sub-assembly.



94. INSTALL ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.