Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Separate Type Yaw Rate Sensor)

DTC    B1608/84    Front Satellite Sensor Bus LH Initialization Incomplete

DTC    B1617/84    Lost Communication with Front Airbag Sensor LH

DTC    B1618/84    Front Airbag Sensor LH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1608/84
B1617/84
B1618/84
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit.
  2. Front airbag sensor LH malfunction
  3. Airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Airbag sensor assembly

WIRING DIAGRAM


C244889E02


INSPECTION PROCEDURE

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)


    C238216E03
  1. Connect the connectors that link the engine room main wire and instrument panel wire.

  1. Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - A12-1 (-SL)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 7
OK


3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)


    C238212E06
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - A12-1 (-SL)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 8
OK


4.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)


    C238212E06
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - Body ground
    Power switch on (IG)
    Below 1 V
    A12-1 (-SL) - Body ground
    Power switch on (IG)
    Below 1 V

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 9
OK


5.CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)


    C238212E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A12-1 (-SL) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *a
    Front view of wire harness connector
    (to Front Airbag Sensor LH)



NG
Go to step 10
OK


6.CHECK FRONT AIRBAG SENSOR LH


    C238211E01
  1. Connect the connector to the airbag sensor assembly.

  1. Interchange the front airbag sensor LH with RH and connect the connectors.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 are not output.
    A
    DTC B1608/84, B1617/84 or B1618/84 is output.
    B
    DTC B1603/83, B1612/83 or B1613/83 is output.
    C

    HINT:
    Codes other than DTCs B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Return the front airbag sensor LH and RH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Front Airbag Sensor RH
    *2
    Airbag Sensor Assembly



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE FRONT AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK INSTRUMENT PANEL WIRE (OPEN)


    C247432E01
  1. Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    The service wire has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IA5-3 (+SL) - IA5-4 (-SL)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

8.CHECK INSTRUMENT PANEL WIRE (SHORT)


    C247431E02
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IA5-3 (+SL) - IA5-4 (-SL)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)


    C247431E02
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    IA5-3 (+SL) - Body ground
    Power switch on (IG)
    Below 1 V
    IA5-4 (-SL) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE 

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)


    C247431E02
  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IA5-3 (+SL) - Body ground
    Always
    1 MΩ or higher
    IA5-4 (-SL) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Front Airbag Sensor LH
    *2
    Airbag Sensor Assembly
    *3
    Engine Room Main Wire
    *4
    Instrument Panel Wire
    *a
    Front view of wire harness connector
    (to Engine Room Main Wire)



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE