Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3004-800    High Voltage Power Resource

DTC    P3004-801    High Voltage Power Resource

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0AE6-225 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3004
800
Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
  1. Wire harness or connector
  2. No. 4 engine wire
  3. Compressor with motor assembly
  4. Inverter with converter assembly
  5. Hybrid battery junction block assembly
  6. No. 4 floor wire
  7. Power management control ECU
801
Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).

WIRING DIAGRAM

  1. Refer to the wiring diagram for DTC P0A08-264 .
  2. Refer to the wiring diagram for DTC P0AA6-526 .
  3. Refer to the wiring diagram for DTC P0AE6-225 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3004-800 or P3004-801 only is output.
    A
    DTCs shown in Table 1 are output simultaneously.
    B
    DTCs shown in Table 2 are output simultaneously.
    C


    Table 1 
    DTC No.
    Relevant Diagnosis
    P0A09-265
    DC/DC Converter Status Circuit Low Input
    P0A10-263
    DC/DC Converter Status Circuit High Input

    Table 2 
    DTC No.
    Relevant Diagnosis
    P0ABF-123
    Hybrid Battery Pack Current Sensor Circuit
    P0AC0-123
    Hybrid Battery Pack Current Sensor Circuit Range / Performance
    P0AC1-123
    Hybrid Battery Pack Current Sensor Circuit Low
    P0AC2-123
    Hybrid Battery Pack Current Sensor Circuit High
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123
    Hybrid Battery Voltage Sensor "A" Circuit Low
    P0B42-123
    Hybrid Battery Voltage Sensor "B" Circuit Low
    P0B47-123
    Hybrid Battery Voltage Sensor "C" Circuit Low
    P0B4C-123
    Hybrid Battery Voltage Sensor "D" Circuit Low
    P0B51-123
    Hybrid Battery Voltage Sensor "E" Circuit Low
    P0B56-123
    Hybrid Battery Voltage Sensor "F" Circuit Low
    P0B5B-123
    Hybrid Battery Voltage Sensor "G" Circuit Low
    P0B60-123
    Hybrid Battery Voltage Sensor "H" Circuit Low
    P0B65-123
    Hybrid Battery Voltage Sensor "I" Circuit Low
    P0B6A-123
    Hybrid Battery Voltage Sensor "J" Circuit Low
    P0B6F-123
    Hybrid Battery Voltage Sensor "K" Circuit Low
    P0B74-123
    Hybrid Battery Voltage Sensor "L" Circuit Low
    P0B79-123
    Hybrid Battery Voltage Sensor "M" Circuit Low
    P0B7E-123
    Hybrid Battery Voltage Sensor "N" Circuit Low
    P0B83-123
    Hybrid Battery Voltage Sensor "O" Circuit Low
    P0B88-123
    Hybrid Battery Voltage Sensor "P" Circuit Low
    P0B8D-123
    Hybrid Battery Voltage Sensor "Q" Circuit Low
    P0B92-123
    Hybrid Battery Voltage Sensor "R" Circuit Low
    P308A-123
    Hybrid Battery Voltage Sensor All Circuits Low
    U029A-123
    Lost Communication with Hybrid Battery Pack Sensor Module

    HINT:
    P3004-800 or P3004-801 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)

C
GO TO DTC CHART (HYBRID BATTERY SYSTEM) (Click here)
A


2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A264189
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A259713E01
  1. Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.



    A260188E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    (Tester Probe Polarity)
    Switch Condition
    Specified Condition
    G2-1 (ACPE) (Negative probe) - G2-2 (ACPB) (Positive probe)
    Power switch off
    100 kΩ or higher

    Text in Illustration 
    *a
    Front view of No. 4 engine wire (Air Conditioning Harness) connector
    (to Inverter with Converter Assembly)

    NOTICE:
    1. Do not use a megohmmeter.
    2. Read the resistance after the value has stabilized.

    HINT:
    The polarities of the tester probes may differ depending on the tester. Use the current output probe of the tester as the positive probe for this measurement. To determine the polarity, use another voltmeter to confirm the current output probe of the tester. When measuring the output of the tester, the voltmeter positive probe indicates the tester current output probe.

  1. Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.



NG
Go to step 7
OK


4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A13 from the inverter with converter assembly.

  1. Disconnect connector A38 from power management control ECU.



    A259909E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    A13-5 (NODD) - A38-21 (NODD)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    A13-5 (NODD) or A38-21 (NODD) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the power management control ECU connector.

  1. Connect the inverter with converter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK POWER MANAGEMENT CONTROL ECU

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).



    A249277E63
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A38-21(NODD) - I3-6(E1)
    Power switch on (IG)
    Less than 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


6.CHECK NO. 4 FLOOR WIRE

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A259710
  1. Remove the connector cover assembly from the inverter with converter assembly.



    A259712E04
  1. Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.

  1. Remove the No. 4 hybrid battery shield panel .



    A259724E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q2-1 (CBI) - Q3-1 (CEI)
    Power switch off
    10 kΩ or higher

  1. Install the No. 4 hybrid battery shield panel.

  1. Connect the No. 4 floor wire.

  1. Install the connector cover assembly.



NG
Go to step 8
OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)  

7.CHECK NO. 4 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A259713E01
  1. Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.



    A259733E01
  1. Disconnect connector G1 of the No. 4 engine wire (air conditioning harness) from the compressor with motor assembly.
    Text in Illustration 
    *1
    Green Lock



    A260188E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G2-1 (ACPE) - G2-2 (ACPB)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of No. 4 engine wire (Air Conditioning Harness) connector
    (to Inverter with Converter Assembly)

  1. Connect the No. 4 engine wire (air conditioning harness) to the compressor with motor assembly.

  1. Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.



NG
REPLACE NO. 4 ENGINE WIRE
OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY (Click here)  

8.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 4 hybrid battery shield panel .



    A259723E04
  1. Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.



    A260252E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Q3-1 (CEI) - Q2-1 (CBI)
    Power switch off
    10 kΩ or higher

  1. Connect the No. 4 floor wire.

  1. Install the No. 4 hybrid battery shield panel.



NG
REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE NO. 4 FLOOR WIRE (Click here)