DTC P3004-800 High Voltage Power Resource |
DTC P3004-801 High Voltage Power Resource |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3004 | 800 | Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on). |
|
| 801 | Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on). |
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| P3004-800 or P3004-801 only is output. | A |
| DTCs shown in Table 1 are output simultaneously. | B |
| DTCs shown in Table 2 are output simultaneously. | C |
| DTC No. | Relevant Diagnosis |
| P0A09-265 | DC/DC Converter Status Circuit Low Input |
| P0A10-263 | DC/DC Converter Status Circuit High Input |
| DTC No. | Relevant Diagnosis |
| P0ABF-123 | Hybrid Battery Pack Current Sensor Circuit |
| P0AC0-123 | Hybrid Battery Pack Current Sensor Circuit Range / Performance |
| P0AC1-123 | Hybrid Battery Pack Current Sensor Circuit Low |
| P0AC2-123 | Hybrid Battery Pack Current Sensor Circuit High |
| P0AFC-123 | Hybrid Battery Pack Sensor Module |
| P0B3D-123 | Hybrid Battery Voltage Sensor "A" Circuit Low |
| P0B42-123 | Hybrid Battery Voltage Sensor "B" Circuit Low |
| P0B47-123 | Hybrid Battery Voltage Sensor "C" Circuit Low |
| P0B4C-123 | Hybrid Battery Voltage Sensor "D" Circuit Low |
| P0B51-123 | Hybrid Battery Voltage Sensor "E" Circuit Low |
| P0B56-123 | Hybrid Battery Voltage Sensor "F" Circuit Low |
| P0B5B-123 | Hybrid Battery Voltage Sensor "G" Circuit Low |
| P0B60-123 | Hybrid Battery Voltage Sensor "H" Circuit Low |
| P0B65-123 | Hybrid Battery Voltage Sensor "I" Circuit Low |
| P0B6A-123 | Hybrid Battery Voltage Sensor "J" Circuit Low |
| P0B6F-123 | Hybrid Battery Voltage Sensor "K" Circuit Low |
| P0B74-123 | Hybrid Battery Voltage Sensor "L" Circuit Low |
| P0B79-123 | Hybrid Battery Voltage Sensor "M" Circuit Low |
| P0B7E-123 | Hybrid Battery Voltage Sensor "N" Circuit Low |
| P0B83-123 | Hybrid Battery Voltage Sensor "O" Circuit Low |
| P0B88-123 | Hybrid Battery Voltage Sensor "P" Circuit Low |
| P0B8D-123 | Hybrid Battery Voltage Sensor "Q" Circuit Low |
| P0B92-123 | Hybrid Battery Voltage Sensor "R" Circuit Low |
| P308A-123 | Hybrid Battery Voltage Sensor All Circuits Low |
| U029A-123 | Lost Communication with Hybrid Battery Pack Sensor Module |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).
|
| ||||
| OK | |
| 3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY |
Check that the service plug grip is not installed.
![]() |
Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Tester Probe Polarity) | Switch Condition | Specified Condition |
| G2-1 (ACPE) (Negative probe) - G2-2 (ACPB) (Positive probe) | Power switch off | 100 kΩ or higher |
| *a | Front view of No. 4 engine wire (Air Conditioning Harness) connector (to Inverter with Converter Assembly) |
Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY) |
Check that the service plug grip is not installed.
Disconnect connector A13 from the inverter with converter assembly.
Disconnect connector A38 from power management control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A13-5 (NODD) - A38-23 (NODD) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| A13-5 (NODD) or A38-23 (NODD) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Inverter with Converter Assembly) |
| *b | Rear view of wire harness connector (to Power Management Control ECU) |
Connect the power management control ECU connector.
Connect the inverter with converter assembly connector.
|
| ||||
| OK | |
| 5.CHECK POWER MANAGEMENT CONTROL ECU |
Check that the service plug grip is not installed.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A38-23 (NODD) - I3-6 (E1) | Power switch on (IG) | Less than 1.5 V |
| *a | Component with harness connected (Power Management Control ECU) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
|
| ||||
| OK | |
| 6.CHECK NO. 4 FLOOR WIRE |
Check that the service plug grip is not installed.
![]() |
Remove the connector cover assembly from the inverter with converter assembly.
![]() |
Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.
Remove the No. 4 hybrid battery shield panel .
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Q2-1 (CBI) - Q3-1 (CEI) | Power switch off | 10 kΩ or higher |
Install the No. 4 hybrid battery shield panel.
Connect the No. 4 floor wire.
Install the connector cover assembly.
|
| ||||
| OK | ||
| ||
| 7.CHECK NO. 4 ENGINE WIRE |
Check that the service plug grip is not installed.
![]() |
Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.
![]() |
Disconnect connector G1 of the No. 4 engine wire (air conditioning harness) from the compressor with motor assembly.
| *1 | Green Lock |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| G2-1 (ACPE) - G2-2 (ACPB) | Power switch off | 10 kΩ or higher |
| *a | Front view of No. 4 engine wire (Air Conditioning Harness) connector (to Inverter with Converter Assembly) |
Connect the No. 4 engine wire (air conditioning harness) to the compressor with motor assembly.
Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.
|
| ||||
| OK | ||
| ||
| 8.CHECK HYBRID BATTERY JUNCTION BLOCK ASSEMBLY |
Check that the service plug grip is not installed.
Remove the No. 4 hybrid battery shield panel .
![]() |
Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Q3-1 (CEI) - Q2-1 (CBI) | Power switch off | 10 kΩ or higher |
Connect the No. 4 floor wire.
Install the No. 4 hybrid battery shield panel.
|
| ||||
| OK | ||
| ||