Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight Dimmer Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives the following switch information:
  1. Light control switch is in off, tail, head or AUTO position
  2. Dimmer switch is in high, low or high flash (pass) position
  3. Front fog light switch is in on or off position
  4. Rear fog light switch is in on or off position

WIRING DIAGRAM


for LHD

E231440E02


for RHD

E223764E05


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Dimmer switch high position signal/ON or OFF
    ON: Dimmer switch in high or high flash position
    OFF: Dimmer switch in low position
    -
    Passing Light SW
    Dimmer switch high flash position (pass) signal/ON or OFF
    ON: Dimmer switch in high flash position
    OFF: Dimmer switch not in high flash position
    -
    Rear Fog Light SW
    Rear fog light switch signal/ON or OFF
    ON: Rear fog light switch on
    OFF: Rear fog light switch off
    -
    Front Fog Light SW
    Front fog light switch signal/ON or OFF
    ON: Front fog light switch on
    OFF: Front fog light switch off
    -
    Auto Light SW
    Light control switch AUTO position signal/ON or OFF
    ON: Light control switch in AUTO position
    OFF: Light control switch not in AUTO position
    -
    Head Light SW (Head)
    Light control switch head position signal/ON or OFF
    ON: Light control switch in head position
    OFF: Light control switch not in head position
    -
    Head Light SW (Tail)
    Light control switch tail position signal/ON or OFF
    ON: Light control switch in tail or head position
    OFF: Light control switch in neither tail nor head position
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

HINT:
Inspect the items that did not change as a result of monitoring the Data List.

  1. Remove the headlight dimmer switch assembly (Click here).



  1. for LHD:



      E223779E12
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Light Control Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      18 (T) - 15 (EL)
      Light control switch off
      10 kΩ or higher
      19 (H) - 15 (EL)
      Light control switch off
      10 kΩ or higher
      20 (A) - 15 (EL)
      Light control switch off
      10 kΩ or higher
      18 (T) - 15 (EL)
      Light control switch in tail position
      Below 1 Ω
      18 (T) - 15 (EL)
      Light control switch in head position
      Below 1 Ω
      19 (H) - 15 (EL)
      Light control switch in head position
      Below 1 Ω
      20 (A) - 15 (EL)
      Light control switch in AUTO position
      Below 1 Ω
      Dimmer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      14 (HU) - 15 (EL)
      Dimmer switch in low position
      10 kΩ or higher
      14 (HU) - 15 (EL)
      Dimmer switch in high position
      Below 1 Ω
      17 (HF) - 15 (EL)
      Dimmer switch in high flash position
      Below 1 Ω
      Front Fog Light Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      9 (BFG) - 8 (LFG)
      Fog light switch off
      10 kΩ or higher
      9 (BFG) - 8 (LFG)
      Fog light switch on
      Below 1 Ω
      Rear Fog Light Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      7 (B) - 8 (LFG)
      Rear fog light switch off
      10 kΩ or higher
      7 (B) - 8 (LFG)
      Rear fog light switch on
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



  1. for RHD:



      E223779E09
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Light Control Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      13 (T) - 16 (EL)
      Light control switch off
      10 kΩ or higher
      12 (H) - 16 (EL)
      Light control switch off
      10 kΩ or higher
      11 (A) - 16 (EL)
      Light control switch off
      10 kΩ or higher
      13 (T) - 16 (EL)
      Light control switch in tail position
      Below 1 Ω
      13 (T) - 16 (EL)
      Light control switch in head position
      Below 1 Ω
      12 (H) - 16 (EL)
      Light control switch in head position
      Below 1 Ω
      11 (A) - 16 (EL)
      Light control switch in AUTO position
      Below 1 Ω
      Dimmer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      17 (HU) - 16 (EL)
      Dimmer switch in low position
      10 kΩ or higher
      17 (HU) - 16 (EL)
      Dimmer switch in high position
      Below 1 Ω
      14 (HF) - 16 (EL)
      Dimmer switch in high flash position
      Below 1 Ω
      Front Fog Light Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      2 (BFG) - 3 (LFG)
      Fog light switch off
      10 kΩ or higher
      2 (BFG) - 3 (LFG)
      Fog light switch on
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH ASSEMBLY)
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I25-9 (BFG) - I13-27 (FFOG)
      Always
      Below 1 Ω
      I25-7 (B) - I13-23 (RFOG)
      Always
      Below 1 Ω
      I25-14 (HU) - I13-5 (HU)
      Always
      Below 1 Ω
      I25-17 (HF) - I13-8 (HF)
      Always
      Below 1 Ω
      I25-18 (T) - I13-30 (TAIL)
      Always
      Below 1 Ω
      I25-19 (H) - I13-29 (HEAD)
      Always
      Below 1 Ω
      I25-20 (A) - I13-28 (A)
      Always
      Below 1 Ω
      I25-9 (BFG) - Body ground
      Always
      10 kΩ or higher
      I25-7 (B) - Body ground
      Always
      10 kΩ or higher
      I25-14 (HU) - Body ground
      Always
      10 kΩ or higher
      I25-17 (HF) - Body ground
      Always
      10 kΩ or higher
      I25-18 (T) - Body ground
      Always
      10 kΩ or higher
      I25-19 (H) - Body ground
      Always
      10 kΩ or higher
      I25-20 (A) - Body ground
      Always
      10 kΩ or higher
      I25-15 (EL) - Body ground
      Always
      Below 1 Ω
      I25-8 (LFG) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I25-2 (BFG) - I13-27 (FFOG)
      Always
      Below 1 Ω
      I25-17 (HU) - I13-5 (HU)
      Always
      Below 1 Ω
      I25-14 (HF) - I13-8 (HF)
      Always
      Below 1 Ω
      I25-13 (T) - I13-30 (TAIL)
      Always
      Below 1 Ω
      I25-12 (H) - I13-29 (HEAD)
      Always
      Below 1 Ω
      I25-11 (A) - I13-28 (A)
      Always
      Below 1 Ω
      I25-2 (BFG) - Body ground
      Always
      10 kΩ or higher
      I25-17 (HU) - Body ground
      Always
      10 kΩ or higher
      I25-14 (HF) - Body ground
      Always
      10 kΩ or higher
      I25-13 (T) - Body ground
      Always
      10 kΩ or higher
      I25-12 (H) - Body ground
      Always
      10 kΩ or higher
      I25-11 (A) - Body ground
      Always
      10 kΩ or higher
      I25-16 (EL) - Body ground
      Always
      Below 1 Ω
      I25-3 (LFG) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)