FRONT DOOR > DISASSEMBLY |
| 1. PRECAUTION |
| 2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.
| 5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish.
| 6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.
| 7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
| 8. REMOVE FRONT ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.
| 9. REMOVE COURTESY LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *A | for LH Side |
| *B | for RH Side |
| *1 | Protective Tape |
Disconnect the connector and remove the courtesy light assembly.
| 10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the front door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 10 clips.
![]() |
Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Front Door Inner Glass Weatherstrip |
Disengage the reference boss from the front door panel.
Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
Disconnect the connector.
![]() |
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
| 11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.
| 12. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY |
![]() |
Disengage the 3 clamps and claw, and remove the front door inside handle illumination light assembly.
| 13. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 4 screws.
![]() |
Disengage the 2 claws and remove the front No. 1 speaker assembly.
| 15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 bolts.
Disengage the claw and remove the outer rear view mirror assembly.
| 16. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Disconnect each connector.
Disengage the 4 clamps.
Remove the front door service hole cover.
| 17. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the grommet.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network master switch assembly.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
| 18. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
| 19. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.
| 20. REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION |
![]() |
Remove the 2 bolts.
| *1 | Double-sided Tape |
Disengage the 2 guides and remove the No. 2 front door stiffener cushion.
| 21. REMOVE FRONT DOOR GLASS RUN |
![]() |
Remove the front door glass run.
| 22. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts.
Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.
| 23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts.
Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) |
![]() |
Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.
| 26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.
| 27. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Disengage the 2 claws.
Using a screwdriver, disconnect the connector.
![]() |
Remove the front door outside handle assembly as shown in the illustration.
| 28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Disengage the 3 claws and remove the front door front outside handle pad.
| 29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Disengage the 2 claws and remove the front door rear outside handle pad.
| 30. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY |
![]() |
Using a T30 "TORX" socket wrench, remove the 3 screws.
| *1 | Front Door Lock Open Rod |
Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.
When reusing the front door lock with motor assembly:
![]() |
Remove the door lock wiring harness seal from the front door lock with motor assembly.
| 31. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Remove the front door lock remote control cable assembly.
| 32. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws.
![]() |
Remove the front door inside locking cable assembly.
| 33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Disengage the 3 clamps.
![]() |
Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.
| 34. REMOVE FRONT DOOR WIRE |
![]() |
Disengage the 3 clamps and remove the front door wire.
| 35. REMOVE FRONT DOOR LOCK OPEN ROD |
![]() |
Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
| 36. REMOVE FRONT DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts and front door check assembly.
| 37. REMOVE FRONT DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.
| 38. REMOVE DOOR FRAME GARNISH |
![]() |
Disengage the clip and remove the door frame garnish.
| 39. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.
| 40. REMOVE FRONT DOOR PANEL CUSHION |
![]() |
Disengage the 2 claws and remove the 2 front door panel cushions.
| 41. REMOVE FRONT DOOR VENT SEAL |
![]() |
Remove the front door vent seal.
| 42. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Put protective tape around the front door belt moulding assembly.
| *1 | Protective Tape |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the front door belt moulding assembly.
| *1 | Protective Tape |
| 43. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Using a heat light, heat the front door rear window frame moulding.
![]() |
Using a moulding remover, disengage the clip and remove the front door rear window frame moulding.
| *1 | Double-sided Tape |
| *2 | Caulking Sponge |
| 44. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING |
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
![]() |
Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Dimension |
| A | 5.0 mm |
Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.
| 45. REMOVE FRONT DOOR STRIPE |
Using a heat light, heat the front door stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Front Door Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door stripe to remove it.
| 46. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE |
Using a heat light, heat the front door lower outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Front Door Rear Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the front door lower outside stripe to remove it.