FRONT DOOR > REASSEMBLY |
| 1. PRECAUTION |
| 2. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

| *A | Pressing Forward | *B | Pulling |
| *1 | Non-padded Side | *2 | Padded Side |
| *3 | Squeegee | *4 | Black Out Tape |
| *5 | Release Paper | - | - |
| *a | Side View | - | - |
| Area | Measurement |
| A | 10 to 20 mm (0.393 to 0.787 in.) |
| B | 30 to 70 mm/sec. (1.18 to 2.76 in./sec.) |
| C | 40 to 50° (for pressing forward) |
| D | 30 to 45° (for pulling) |
Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
| *1 | Squeegee |
| *2 | Hem |
| *a | First |
| *b | Second |
| *c | Third |
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 3. INSTALL FRONT DOOR LOWER OUTSIDE STRIPE |
Refer to the illustration to position the front door lower outside stripe.

| *A | LH Side | *B | RH Side |
| *a | Edge of Curved Surface | *b | Square |
| *c | Round | - | - |
| Dimension | Measurement |
| A | 1.5 mm (0.0591 in.) |
| B | 1.0 mm (0.0394 in.) |
Remove the release paper and apply the stripe.
| 4. INSTALL FRONT DOOR STRIPE |
Refer to the illustration to position a new front door stripe.

| *A | LH Side | *B | RH Side |
| *a | Edge of Curved Surface | *b | Square |
| *c | Round | - | - |
| Dimension | Measurement |
| A | 1.5 mm (0.0591 in.) |
| B | 1.0 mm (0.0394 in.) |
Remove the release paper and apply the stripe.
| 5. INSTALL FRONT DOOR UPPER WINDOW FRAME MOULDING |
![]() |
Engage the claw and guide of the front door upper window frame moulding to the door frame.
Using an air riveter or hand riveter with a nose piece, install the front door upper window frame moulding with 7 new rivets.
![]() |
| *1 | Riveter |
| *2 | Mandrel |
| *a | Incorrect |
![]() |
| *1 | Riveter |
| *a | Incorrect |
![]() |
| *1 | Riveter |
| *a | Incorrect |
| 6. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
![]() |
Install a new front door rear window frame moulding.
| *1 | Double-sided Tape |
| *2 | Caulking Sponge |
Using a heat light, heat the vehicle body and front door rear window frame moulding.
Remove the release paper from the face of the front door rear window frame moulding.
Install the front door rear window frame moulding with the clip.
| 7. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 6 claws to install the front door belt moulding assembly.
| 8. INSTALL FRONT DOOR VENT SEAL |
![]() |
Install the front door vent seal.
| 9. INSTALL FRONT DOOR PANEL CUSHION |
![]() |
Engage the 2 claws to install 2 new front door panel cushions.
| 10. INSTALL FRONT DOOR NO. 2 WEATHERSTRIP |
![]() |
Engage the 8 clips to install the front door No. 2 weatherstrip.
| 11. INSTALL DOOR FRAME GARNISH |
![]() |
Engage the clip to install a new door frame garnish.
| 12. INSTALL FRONT DOOR WEATHERSTRIP |
![]() |
Engage the 19 clips and install the front door weatherstrip.
| 13. INSTALL FRONT DOOR CHECK ASSEMBLY |
Apply MP grease to the sliding areas of the front door check assembly.
Apply adhesive to the threads of the bolt (A).
![]() |
Install the front door check assembly with the 3 bolts.
| 14. INSTALL FRONT DOOR LOCK OPEN ROD |
![]() |
Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
| 15. INSTALL FRONT DOOR WIRE |
![]() |
Engage the 3 clamps to install the front door wire.
| 16. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
![]() |
Engage the claw.
| *1 | Door Handle Nut |
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw and door handle nut.
![]() |
Engage the 3 clamps.
Connect the connector.
| 17. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the front door inside locking cable assembly.
![]() |
Engage the 3 claws.
| 18. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the front door lock remote control cable assembly.
| 19. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY |
Apply MP grease to the sliding parts of the front door lock with motor assembly.
When reusing the front door lock with motor assembly:
![]() |
Install a new door lock wiring harness seal to the front door lock with motor assembly.
![]() |
Insert the front door lock open rod to the front door lock with motor assembly.
| *1 | Front Door Lock Open Rod |
Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.
| 20. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Engage the 2 claws to install the front door rear outside handle pad.
| 21. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Engage the 3 claws to install the front door front outside handle pad.
| 22. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Insert the front end of the front door outside handle assembly into the front door outside handle frame.
Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.
![]() |
Connect the connector.
Engage the 2 claws.
| 23. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side) |
![]() |
Engage the 2 guides and claw, and install the front door outside handle cover to the lock cylinder assembly as shown in the illustration.
| 24. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side) |
![]() |
Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
![]() |
Install the hole plug.
| 25. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.
![]() |
Install the hole plug.
| 26. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide as shown in the illustration.
Install the front door rear lower frame sub-assembly with the 2 bolts.
| 27. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide as shown in the illustration.
Install the front door front lower frame sub-assembly with the 2 bolts.
| 28. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 29. INSTALL NO. 2 FRONT DOOR STIFFENER CUSHION |
Clean the front door panel sub-assembly.
![]() |
Engage the 2 guides.
| *1 | Double-sided Tape |
Install a new No. 2 front door stiffener cushion with the 2 bolts.
| 30. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.
| 31. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the temporary bolt to the front door window regulator assembly.
![]() |
Temporarily install the front door window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.
| 32. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network master switch assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the grommet.
| 33. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply new butyl tape to the front door panel.
![]() |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
| *1 | Reference Point |
Attach the front door service hole cover according to the reference points on the front door panel.
Engage the 4 clamps.
Connect each connector.
| 34. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY |
Engage the claw to temporarily install the outer rear view mirror assembly.
Install the outer rear view mirror assembly with the 3 bolts.
Connect the connector.
| 35. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
Engage the 2 claws to the vehicle body to temporarily install the front No. 1 speaker assembly.
![]() |
Install the front No. 1 speaker assembly with the 4 screws.
| *A | LH Side |
| *B | RH Side |
Connect the connector.
| 36. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the front door inner glass weatherstrip.
| 37. INSTALL FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY |
Engage the claw and 3 clamps to install the front door inside handle illumination light assembly.
| 38. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
| 39. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Connect the connector.
![]() |
Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 10 clips and install the front door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 40. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| *A | for LH Side |
| *B | for RH Side |
| 41. INSTALL FRONT ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.
| 42. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
Connect each connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the multiplex network master switch assembly with front door armrest base panel.
| 43. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.
| 44. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the 3 clips to install the front door lower frame bracket garnish.
| 45. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the front door inside handle bezel plug.
| 46. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 47. INSTALL LUGGAGE TRIM SERVICE HOLE COVER |
Engage the claw to connect the luggage trim service hole cover.
| 48. INITIALIZE POWER WINDOW CONTROL SYSTEM |
| 49. INSPECT POWER WINDOW OPERATION |