POWER WINDOW REGULATOR MOTOR (for Rear Door) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 3. DISCONNECT CABLE FROM AUXILIARY NEGATIVE BATTERY TERMINAL |
| 4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
| 5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 6. REMOVE REAR ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
| 7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 9. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector and remove the rear door service hole cover.
| 10. DISCONNECT REAR DOOR WEATHERSTRIP |
![]() |
Disconnect the upper part of rear door weatherstrip as shown in the illustration.
| 11. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.
| 13. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
| 14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 15. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 3 bolts.
Remove the rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
| 16. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.