Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT

FRONT AXLE HUB BOLT > REPLACEMENT

for Preparation Click here


NOTICE:
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. DISABLE BRAKE CONTROL (for LHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C239901
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. DISABLE BRAKE CONTROL (for RHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C242738
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE FRONT WHEEL


7. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the front flexible hose.



8. REMOVE FRONT DISC


    C238490E01
  1. Put matchmarks on the front disc and the front axle hub.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the front disc.



9. REMOVE FRONT AXLE HUB BOLT


    C238962
  1. Position the front axle hub bolt to be removed as shown in the illustration.



    C239298E01
  1. Temporarily install 2 nuts to the front axle hub bolts as shown in the illustration.
    Text in Illustration 
    *1
    Nut

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    NOTICE:
    Install the nuts to prevent damage to the front axle hub bolts.

  1. Using SST and a screwdriver or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.

    SST
    09628-10011  



10. INSTALL FRONT AXLE HUB BOLT


    C238962
  1. Position a new front axle hub bolt as shown in the illustration.

  1. Temporarily install the front axle hub bolt to the front axle hub.



    C239299E01
  1. Install a washer and nut to the front axle hub bolt as shown in the illustration.
    Text in Illustration 
    *1
    Nut
    *2
    Washer

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    HINT:
    Recommended washer thickness is 5 mm (0.197 in.) or more.

  1. Using a screwdriver or an equivalent tool to hold the front axle hub, install the front axle hub bolt by tightening the nut.

    NOTICE:
    1. Install the nuts to prevent damage to the front axle hub bolts.
    2. Do not damage the threads of the front axle hub bolts.

  1. Remove the 3 nuts and washer from the 3 front axle hub bolts.



11. INSTALL FRONT DISC


    C238490E01
  1. Align the matchmarks of the front disc and front axle hub, and install the front disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



12. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1090 kgf*cm , 79 ft.*lbf }

    NOTICE:
    Do not twist the flexible hose when installing the front disc brake caliper assembly.



13. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Connect the reservoir level switch connector.

  1. Clear the DTCs (Click here).



15. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



16. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)