Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT

REAR AXLE HUB BOLT > REPLACEMENT

for Preparation Click here


NOTICE:
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. DISABLE BRAKE CONTROL (for LHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C239901
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. DISABLE BRAKE CONTROL (for RHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C242738
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE REAR WHEEL


7. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C083014
  1. Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.

  1. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear flexible hose.



8. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Remove the parking brake shoe adjusting hole plug.



9. REMOVE REAR DISC


    C238505E01
  1. Put matchmarks on the rear disc and the rear axle hub.
    Text in Illustration 
    *a
    Matchmark



    C201774
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.



10. REMOVE REAR AXLE HUB BOLT


    C240540E01
  1. Temporarily install 2 nuts to the rear axle hub bolts as shown in the illustration.
    Text in Illustration 
    *1
    Nut

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    NOTICE:
    Install the nuts to prevent damage to the rear axle hub bolts.

  1. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

    SST
    09611-12010  

    NOTICE:
    Do not damage the threads of the rear axle hub bolts.



11. INSTALL REAR AXLE HUB BOLT


    C240541E01
  1. Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
    Text in Illustration 
    *1
    Nut
    *2
    Washer

  1. Install a washer and nut to the rear axle hub bolt as shown in the illustration.

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    HINT:
    Recommended washer thickness is 5 mm (0.197 in.) or more.

  1. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

    NOTICE:
    1. Install the nuts to prevent damage to the rear axle hub bolts.
    2. Do not damage the threads of the rear axle hub bolts.

  1. Remove the 3 nuts and washer from the 3 rear axle hub bolts.



12. INSTALL REAR DISC


    C238505E01
  1. Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the rear disc has minimal runout.



13. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



14. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    62 N*m{ 630 kgf*cm , 46 ft.*lbf }

  1. Install the rear flexible hose to the rear shock absorber assembly with the bolt.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }



15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Connect the reservoir level switch connector.

  1. Clear the DTCs (Click here).



16. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



17. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)



18. ADJUST PARKING BRAKE
(Click here)


19. INSTALL REAR WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }