Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

DTC    B15DA    Rear Console Recognition Disconnected

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and cooler control switch assembly are connected via AVC-LAN communication lines.
This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and cooler control switch.

DTC No.
DTC Detection Condition
Trouble Area
B15DA
When either of the following conditions is met:
  1. The cooler control switch assembly was not connected while the power switch was on (IG) or on (ACC).
  2. Communication between the master unit and the cooler control switch assembly was not possible when the hybrid system was started.
  1. Cooler control switch assembly power source circuit
  2. AVC-LAN circuit between radio and display receiver assembly and cooler control switch assembly
  3. Cooler control switch assembly
  4. Radio and display receiver assembly
  5. Harness or connector

HINT:
The radio and display receiver assembly is the master unit.


WIRING DIAGRAM


E299415E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check that optional components (including associated wiring) which generate radio waves are not installed.

    Result:
    Result
    Proceed to
    Optional components (including associated wiring) are installed.
    A
    Optional components (including associated wiring) are not installed.
    B

    HINT:
    1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
    2. These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END 

4.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
  1. Disconnect the X1 cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X1-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    X1-1 (+B) - X1-16 (GND)
    Power switch off
    11 to 14 V
    X1-7 (IG+) - X1-16 (GND)
    Power switch on (IG)
    11 to 14 V
    X1-6 (ACC) - X1-16 (GND)
    Power switch on (ACC)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the X1 cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-7 (TX1+) - X1-15 (TX+)
    Always
    Below 1 Ω
    I155-8 (TX1-) - X1-5 (TX-)
    Always
    Below 1 Ω
    I155-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    I155-8 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE COOLER CONTROL SWITCH ASSEMBLY
  1. Replace the cooler control switch assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END