Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE DOOR HINGE TORSION BAR

LUGGAGE DOOR HINGE TORSION BAR > INSTALLATION

for Preparation Click here


NOTICE:
After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.



1. INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT


    B280586
  1. Install a new luggage compartment door torsion bar support as shown in the illustration.



2. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH
  1. Check the identification mark on the luggage door hinge torsion bar RH.

    Color:
    Green



    B280587E01
  1. Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.
    Text in Illustration 
    *a
    Installation Hole
    *b
    Installation Hole (for Adjustment)



    B280584
  1. Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.



    B280582
  1. Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.



    B280580E01
  1. Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.

    SST
    09804-24010  

  1. Remove the protective tape.



3. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH
  1. Check the identification mark on the luggage door hinge torsion bar RH.

    Color:
    White



    B280588E01
  1. Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.
    Text in Illustration 
    *a
    Installation Hole
    *b
    Installation Hole (for Adjustment)



    B280578
  1. Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.



    B280576
  1. Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.



    B280574E01
  1. Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.

    SST
    09804-24010  



    B280572
  1. Engage the 2 claws as shown in the illustration.



    B287076E01
  1. Connect the rear seatback lock assembly RH (rear seat lock control cable RH) and engage the hook in the order indicated in the illustration.

  1. Remove the protective tape.



4. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH
  1. Engage the 4 claws and install the luggage compartment door hinge cover LH.



5. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
  1. Install the 3 clips.

  1. Engage the fastener and install the luggage compartment inner trim cover LH.



7. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH
  1. Install the 3 clips.

  1. Engage the fastener and install the luggage compartment inner trim cover RH.



8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    B287055E01
  1. Engage the 2 pins to install the 2 No. 1 luggage compartment trim hooks.
    Text in Illustration 
    *1
    Pin



9. INSTALL LUGGAGE COMPARTMENT FRONT TRIM COVER
  1. Engage the 2 claws.

  1. Engage the 8 fasteners and install the luggage compartment front trim cover.



10. INSTALL REAR FLOOR FINISH PLATE


    B287056
  1. Engage the 4 clips and install the rear floor finish plate.

  1. Install the 5 clips.



11. INSTALL BAGGAGE HOLDER NET
  1. Install the baggage holder net.



12. INSTALL LUGGAGE COMPARTMENT FLOOR MAT
  1. Install the luggage compartment floor mat.