CYLINDER BLOCK > REASSEMBLY |
| 1. INSTALL STUD BOLT |
![]() |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.
| 2. INSTALL NO. 2 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, install the 4 No. 2 oil nozzles sub-assembly with the 4 bolts.
| 3. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, install the 2 No. 1 oil nozzles sub-assembly with the 2 bolts.
| 4. INSTALL PISTON |
Using a small screwdriver, install a new snap ring (rear side) at one end of the piston pin hole.
Gradually heat the piston up to 80 to 90°C (176 to 194°F).
Coat the piston, piston pin and connecting rod with engine oil.
![]() |
Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.
| *a | Front Mark |
![]() |
Using a small screwdriver, install a new snap ring (front side) on the other side of the piston pin hole.
| *1 | Snap Ring |
| *a | Front Mark Cutout Portion |
![]() |
Check the fitting condition between the piston and piston pin.
Move the connecting rod back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
Rotate the piston back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
| 5. INSTALL PISTON RING SET |

| *A | Type A | *B | Type B |
| *1 | Piston | *2 | Oil Ring |
Type A:
![]() |
Install the oil ring expander and oil ring by hand.
| *1 | Oil Ring |
| *2 | Oil Ring Expander |
| *3 | Coil Joint |
| *4 | Oil Ring End |
Type B:
![]() |
Install the oil ring expander, upper oil ring side rail and lower oil ring side rail by hand.
| *1 | Upper Oil Ring Side Rail |
| *2 | Oil Ring Expander |
| *3 | Lower Oil Ring Side Rail |
![]() |
Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring with the code mark positioned as shown in the illustration.
| *1 | No. 1 Compression Ring |
| *2 | No. 2 Compression Ring |
| *a | Piston Ring Expander |
| *b | Code Mark (1N or 1NA) |
| *c | Code Mark (2N) |
| *d | Paint Mark |
![]() | Upward |
| Item | Code Mark |
| No. 1 Compression Ring | 1N or 1NA |
| No. 2 Compression Ring | 2N |
| 6. INSTALL CRANKSHAFT PULLEY KEY |
Install the 2 crankshaft pulley keys to the crankshaft.
| 7. INSTALL CRANKSHAFT BEARING |
![]() |
Clean the main journal and both surfaces of the bearing.
| *a | No. 1, No. 5 Journal Bearing |
| *b | No. 2, No. 4 Journal Bearing |
| *c | No. 3 Journal Bearing |
| *d | Silver |
| *e | Black |
![]() |
Install the upper bearing to the cylinder block as shown in the illustration.
| *a | CORRECT |
| *b | INCORRECT |
![]() |
Install the lower bearing onto the bearing cap.
| *1 | Vernier Caliper |
Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the lower bearing edge.
| 8. INSTALL CRANKSHAFT THRUST WASHER |
Apply engine oil to the thrust washers.
![]() |
Install the 2 thrust washers onto the No. 3 journal position of the cylinder block with the oil grooves facing outward.
| *1 | Oil Groove |
| 9. INSTALL CRANKSHAFT |
Apply engine oil to the upper bearing, and install the crankshaft onto the cylinder block.
![]() |
Examine the front marks and numbers, and install the bearing caps onto the cylinder block with the front marks as shown in the illustration.
| *a | Front Mark |
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Step 1:
![]() |
Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Step 2:
Tighten the 10 bearing cap bolts again in the sequence shown in the illustration.
Step 3:
![]() |
Mark the front of the bearing cap bolts with paint.
| *a | Paint Mark |
![]() | Engine Front |
Tighten the 10 bearing cap bolts 90° in the same sequence.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
| 10. INSTALL CONNECTING ROD BEARING |
![]() |
Clean the bearing contact surface of the connecting rod and cap, and both surfaces of both bearings.
| *1 | Vernier Caliper |
Install the connecting rod bearings to the connecting rods and connecting rod caps.
Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the edges of the bearing cap and connecting rod bearing.
| 11. INSTALL PISTON WITH CONNECTING ROD |

| *A | Type A | *B | Type B |
| *1 | Piston | *2 | Oil Ring |
Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.
Position the piston rings so that the ring ends are as shown in the illustration.

| *A | Type A | *B | Type B |
| *1 | No. 1 Compression Ring | *2 | No. 2 Compression Ring |
| *3 | Oil Ring | *4 | Oil Ring Expander |
| *5 | Oil Ring Expander (Coil Joint) | *6 | Upper Oil Ring Side Rail |
| *7 | Lower Oil Ring Side Rail | - | - |
![]() |
Using a hammer handle and piston ring compressor, press a piston with connecting rod into each cylinder with the front mark of the piston facing forward.
| *a | Front Mark |
![]() |
Check that the front mark of the connecting rod cap is facing in the correct direction.
| *a | Front Mark |
![]() |
Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
Temporarily install the connecting rod bolts.
Step 1:
Alternately tighten the connecting rod bolts in several steps.
![]() |
Step 2:
| *a | Paint Mark |
![]() | Engine Front |
Mark the front of the connecting rod bolts with paint.
Tighten the bolts 90° as shown in the illustration.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.