Home › Brake › BRAKE (REAR) › REAR BRAKE

REAR BRAKE > REMOVAL

for Preparation Click here


NOTICE:
  1. When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
  2. While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. DISABLE BRAKE CONTROL (for LHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C239901
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



5. DISABLE BRAKE CONTROL (for RHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C242738
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE REAR WHEEL


7. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.



8. SEPARATE REAR FLEXIBLE HOSE


    C243121
  1. Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.



9. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY


    C239569E01
  1. Hold the rear disc brake cylinder slide pin, and remove the 2 bolts and rear disc brake cylinder assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Turn



10. REMOVE REAR DISC BRAKE PAD


    C238499
  1. Remove the 2 rear disc brake pads with rear disc brake anti-squeal shim kit from the disc brake cylinder mounting.



11. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT


    C239558
  1. Remove the rear disc brake anti-squeal shim from each rear disc brake pad.



    C239557
  1. Remove the rear disc brake pad wear indicator plate from each rear disc brake pad.



12. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE


    C238500
  1. Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.



13. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Upper Side)


    C243122
  1. Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.



14. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN (for Lower Side)


    C243123
  1. Remove the rear disc brake cylinder slide pin from the disc brake cylinder mounting.



15. REMOVE REAR DISC BRAKE CYLINDER SLIDE BUSHING


    C210924E05
  1. Using a screwdriver with its tip wrapped with vinyl tape, remove the rear disc brake cylinder slide bushing from the rear disc brake cylinder slide pin.
    Text in Illustration 
    *1
    Vinyl Tape

    NOTICE:
    Do not damage the rear disc brake cylinder slide pin.



16. REMOVE REAR DISC BRAKE BUSHING DUST BOOT


    C243124
  1. Remove the 2 rear disc brake bushing dust boots from the disc brake cylinder mounting.



17. REMOVE DISC BRAKE CYLINDER MOUNTING


    C243125
  1. Remove the 2 bolts and disc brake cylinder mounting.



18. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Remove the parking brake shoe adjusting hole plug.



19. REMOVE REAR DISC


    C238505E01
  1. Put matchmarks on the rear disc and the rear axle hub.
    Text in Illustration 
    *a
    Matchmark



    C201774
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.