Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING

SLIDING ROOF HOUSING > REMOVAL

for Preparation Click here



1. REMOVE ROOF HEADLINING ASSEMBLY
(Click here)


2. REMOVE SLIDING ROOF SIDE GARNISH LH


    B279108
  1. Disengage the 2 claws and remove the sliding roof side garnish LH.



3. REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY


    B279109
  1. Using a T25 "TORX" socket wrench, remove the 4 screws and sliding roof glass sub-assembly.

    NOTICE:
    To prevent the sliding roof glass and sliding roof drive gear from being displaced, fully close the sliding roof glass (sliding roof drive cable), and then remove the sliding roof glass sub-assembly.



5. REMOVE SLIDING ROOF PANEL OR REMOVABLE ROOF WEATHERSTRIP
  1. Remove the sliding roof panel or removable roof weatherstrip from the sliding roof panel assembly.



6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:
When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B278804E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock and disconnect the curtain shield airbag connector.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



    B278806
  1. Using a clip remover, remove the pin.

    HINT:
    Perform the same procedure for the other pins.



  1. Using 2 screwdrivers, disengage the 2 claws and remove the clip from the body panel as shown in the illustration.


    B278808E01


    Text in Illustration 
    *1
    Body Panel
    *2
    Curtain Shield Airbag Assembly

    HINT:
    Perform the same procedure for the other clips.



  1. While holding the curtain shield airbag assembly, disengage the 5 claws.


    B278810

    NOTICE:
    When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.



  1. Remove the 2 bolts.


    B278811

  1. Disengage the 2 hooks to remove the curtain shield airbag assembly.

  1. Remove the 2 spacers from the curtain shield airbag assembly.



7. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE REAR NO. 2 SIDE RAIL SPACER LH


    B290008
  1. Disengage the 2 claws and remove the rear No. 2 side rail spacer LH.



9. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE SLIDING ROOF HOUSING ASSEMBLY


    B279111
  1. for Clamp Type:

    1. Disengage the claw and disconnect the sliding roof drain hose.

      HINT:
      Use the same procedure for the other 3 sliding roof drain hoses.



    B279112
  1. for Clip Type:

    1. Expand the clip and disconnect the sliding roof drain hose.

      HINT:
      Use the same procedure for the other 3 sliding roof drain hoses.



  1. Remove the 4 bolts, 8 nuts and sliding roof housing assembly.


    B286381