Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    A261658E01
  1. Install a new fuel suction tube set gasket to the fuel suction tube.
    Text in Illustration 
    *1
    Fuel Suction Tube Set Gasket
    *2
    Suction Filter

  1. Install the fuel suction tube with pump and gauge assembly to the fuel tank.

    NOTICE:
    1. Do not damage the suction filter.
    2. Be careful that the arm of the sender gauge does not bend.



2. INSTALL FUEL TANK VENT TUBE SET PLATE


    A218221E02
  1. Align the mark of the set plate with the fuel suction tube.
    Text in Illustration 
    *a
    Mark

  1. Install the set plate with the 8 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



3. CONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A261659E01
  1. Push the fuel tube joint onto the plug of the fuel suction plate, then install the tube joint clip.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tube Joint
    *3
    Fuel Pump Tube
    *4
    O-ring
    *a
    Correct
    *b
    Incorrect
    *c
    Collar

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube joint and plug before performing this work.
    2. Check that the fuel tube joint is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tube joint cannot be pulled out.

  1. Connect the fuel pump connector.



4. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


5. INSTALL LUGGAGE TRIM SERVICE HOLE COVER
  1. Engage the claw to connect the luggage trim service hole cover.



6. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG) and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



7. INSTALL REAR FLOOR SERVICE HOLE COVER


    A254976
  1. Install the rear floor service hole cover with new butyl tape.
    Text in Illustration 
    V100144
    Butyl Tape



8. INSTALL REAR SEAT CUSHION LOCK HOOK


    B280246
  1. Engage the claw to install a new rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



9. INSTALL REAR SEAT CUSHION ASSEMBLY
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B298857
  1. Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is firmly installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.