Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the front drive inboard joint assembly with ATF.

  1. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.



    C165536
  1. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

    NOTICE:
    1. Face the end gap of the front drive shaft hole snap ring LH downward.
    2. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    3. Do not damage the front axle inboard joint boot.
    4. Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring LH.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



    C240136E01
  1. Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the front drive inboard joint assembly with ATF.

  1. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.

  1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

  1. Install the front drive shaft assembly RH.

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. When inserting the front drive shaft assembly RH, keep it level.



    C239409
  1. Install the bearing bracket hole snap ring and a new bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



    C240137E01
  1. Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



3. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
  1. Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }



4. CONNECT TIE ROD ASSEMBLY
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



5. INSTALL FRONT SPEED SENSOR
  1. Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

    HINT:
    Install the speed sensor harness bracket first and then the front flexible hose.

  1. Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.



6. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



7. INSTALL FRONT AXLE SHAFT NUT
  1. Clean the threaded parts on the front drive shaft assembly and a new axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work even when using a new drive shaft.
    2. Keep the threaded parts free of oil and foreign matter.



    C165538
  1. Using a socket wrench (30 mm), install the front axle shaft nut.

    Torque:
    294 N*m{ 2998 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle shaft nut.



8. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



9. ADD HYBRID TRANSAXLE FLUID


    C243609E01
  1. Add transaxle fluid until the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening.
    Text in Illustration 
    *1
    Filler Nozzle
    *2
    Filler Plug

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Use Toyota Genuine ATF WS.
    3. Be sure to fully insert the filler nozzle into the filler plug opening.
    4. Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.
    5. Be sure to directly check that the transaxle fluid level is within the specified range.
    6. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

    Reference:
    3.7 liters (3.9 US qts, 3.2 lmp.qts)

  1. After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    After adding fluid, make sure to check the fluid level.



10. INSPECT HYBRID TRANSAXLE FLUID


    C244536E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug

  1. Check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Be sure to directly check that the transaxle fluid level is within the specified range.
    3. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.
    4. If the fluid was replaced or fluid was added, make sure to recheck the fluid level after driving the vehicle.

  1. Check for leaks if the quantity of transaxle fluid is low.

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



11. INSPECT FOR TRANSAXLE FLUID LEAK


12. INSTALL FRONT FENDER APRON SEAL LH


13. INSTALL FRONT FENDER APRON SEAL RH


14. INSTALL ENGINE UNDER COVER LH


15. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


16. INSTALL ENGINE UNDER COVER RH


17. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


18. ADJUST FRONT WHEEL ALIGNMENT
(Click here)


19. CHECK FOR SPEED SENSOR SIGNAL
(Click here)