Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT WHEELS


2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


3. REMOVE ENGINE UNDER COVER LH


4. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH


5. REMOVE ENGINE UNDER COVER RH


6. REMOVE FRONT FENDER APRON SEAL LH


7. REMOVE FRONT FENDER APRON SEAL RH


8. DRAIN HYBRID TRANSAXLE FLUID


    C243608E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug
    *2
    Drain Plug

  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket to drain the hybrid transaxle fluid.

  1. Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



9. REMOVE FRONT AXLE SHAFT NUT


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle shaft nut.



10. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C238963
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
    If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



11. SEPARATE FRONT SPEED SENSOR


    C238961
  1. Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.

    NOTICE:
    Be sure to separate the front speed sensor from the front shock absorber assembly completely.



    C238448
  1. Remove the bolt and front speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from contacting the sensor tip.
    2. Be careful not to damage the front speed sensor.
    3. Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.



12. SEPARATE TIE ROD ASSEMBLY


    C238512
  1. Remove the cotter pin and nut.



    C238513E01
  1. Install SST to the tie rod assembly LH.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the lower ends of the tie rod assembly LH and SST are aligned.

  1. Secure SST using a string.

    NOTICE:
    Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



  1. Using SST, separate the tie rod assembly LH from the steering knuckle.


    C238514E02


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Grease Application Area
    V100136
    Place the wrench here.
    -
    -
    SST
    09960-20010   (09961-02010)

    CAUTION:
    Apply grease to the bolt threads and the tip of SST.

    NOTICE:
    1. Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



13. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY


    C238969
  1. Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.



14. SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    C238968E01
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
    If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.



15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C239400E01
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-00031  
    09520-01010  

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly LH.



16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C239409
  1. Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly RH.

  1. Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.



17. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    C057543
  1. Using a screwdriver, remove the front drive shaft hole snap ring LH.