Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)


    C092032E07
  1. Using SST, a steel plate and a press, install a new front drive shaft bearing.
    Text in Illustration 
    *1
    Steel Plate

    SST
    09527-10011  

    NOTICE:
    The bearing should be completely installed.



    C092033
  1. Using a snap ring expander, install a new drive shaft hole snap ring.



2. INSTALL FRONT DRIVE SHAFT DUST COVER (for RH Side)


    F045047E12
  1. Using SST, a steel plate and a press, install a new front drive shaft dust cover.
    Text in Illustration 
    *1
    Steel Plate

    SST
    09726-40010  

    Dimension (A):
    26.6 to 27.6 mm (1.05 to 1.08 in.)

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the front drive shaft dust cover.



3. INSTALL FRONT DRIVE SHAFT DUST COVER RH


    C129109E07
  1. Using a steel plate and a press, install a new front drive shaft dust cover RH until dimension (A) from the tip of the front drive inboard joint assembly to the front drive shaft dust cover RH meets the specification.
    Text in Illustration 
    *1
    Steel Plate

    Dimension (A):
    110.0 to 111.0 mm (4.33 to 4.37 in.)

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the front drive shaft dust cover RH.



4. INSTALL FRONT DRIVE SHAFT DUST COVER LH


    F041033E14
  1. Using a steel plate and a press, install a new front drive shaft dust cover LH.
    Text in Illustration 
    *1
    Steel Plate

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the front drive shaft dust cover LH.



5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT


    C166359E03
  1. Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
    Text in Illustration 
    *1
    Protective Tape



    C240887E01
  1. Install new parts onto the front drive outboard joint shaft assembly in the following order:
    Text in Illustration 
    *1
    Front Drive Outboard Joint Shaft Assembly
    *2
    Front No. 2 Axle Outboard Joint Boot Clamp
    *3
    Front Axle Outboard Joint Boot
    *4
    Front Axle Outboard Joint Boot Clamp
    V100135
    Outboard Joint Side
    V100136
    Inboard Joint Side

    1. Front No. 2 axle outboard joint boot clamp

    2. Front axle outboard joint boot

    3. Front axle outboard joint boot clamp

  1. Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

    Standard grease capacity:
    205 to 215 g (7.23 to 7.58 oz.)

  1. Install the front axle outboard joint boot onto the front drive outboard joint shaft assembly groove.

    NOTICE:
    1. Do not allow grease to adhere to the boot clamp track of the outboard joint boot.
    2. Keep the inside of the outboard joint boot free of foreign matter.



6. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



    C219374
  1. Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot and temporarily fold back the lever.

    NOTICE:
    1. Set the lever into the guide groove correctly and install the clamp as far into the inside of the vehicle as possible.
    2. Check the band and the lever for any deformation before folding back the lever.



    C219375E02
  1. Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work surface. Roll the outboard joint and fold the lever until a click sound can be heard.
    Text in Illustration 
    *a
    Weight
    *b
    Contact

    NOTICE:
    1. Do not damage the speed sensor rotor.
    2. Make sure that the outboard joint is in direct contact with the work surface.



    C219376
  1. Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

    NOTICE:
    1. Do not use too much force when tapping with the plastic hammer.
    2. Do not damage the front axle outboard joint boot.



7. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



    C107948
  1. Install the front axle outboard joint boot clamp onto the front axle outboard joint boot and temporarily fold back the lever.

    NOTICE:
    1. Set the lever into the guide groove correctly.
    2. Check the band and the lever for any deformation before folding back the lever.



    C158356E08
  1. Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.
    Text in Illustration 
    *a
    Place the tip near the center of the lever.



    C112272
  1. Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

    NOTICE:
    Do not damage the front axle outboard joint boot.



8. INSTALL FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)
  1. Install a new front drive shaft damper clamp onto the front drive outboard joint shaft assembly.



    C240143E01
  1. Install the front drive shaft damper onto the front drive outboard joint shaft assembly.
    Text in Illustration 
    *1
    Front Drive Shaft Damper
    *2
    Front Drive Shaft Damper Clamp

  1. Set the dimension as specified below.

    Dimension (A):
    223.4 to 227.4 mm (8.80 to 8.95 in.)

  1. Install the front drive shaft damper clamp onto the front drive shaft damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C135385E09
  1. for One Touch Type:

    1. Using a screwdriver, install the front drive shaft damper clamp.
      Text in Illustration 
      *A
      for One Touch Type
      *B
      for Claw Engagement Type

  1. for Claw Engagement Type:

    1. Using needle nose pliers, install the front drive shaft damper clamp.
      Text in Illustration 
      *a
      Claws



9. INSTALL FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)


    C311997E01
  1. Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.
    Text in Illustration 
    *1
    Front Drive Shaft Damper
    *2
    Front Drive Shaft Damper Clamp

  1. Set the dimension as specified below.

    Dimension (A):
    261.4 to 265.4 mm (10.3 to 10.4 in.)

  1. Install the 2 front drive shaft damper clamps onto the front drive shaft damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C205160E03
  1. Using needle nose pliers, install the 2 front drive shaft damper clamps.
    Text in Illustration 
    *a
    Claws



10. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY


    C104548E15
  1. Install new parts onto the front drive outboard joint shaft assembly in the following order:
    Text in Illustration 
    *1
    Front Axle Inboard Joint Boot Clamp
    *2
    Front Axle Inboard Joint Boot
    *3
    Front No. 2 Axle Inboard Joint Boot Clamp
    *4
    Protective Tape
    V100135
    Outboard Joint Side
    V100136
    Inboard Joint Side

    1. Front axle inboard joint boot clamp

    2. Front axle inboard joint boot

    3. Front No. 2 axle inboard joint boot clamp

  1. Hold the drive shaft in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.



    C067417E26
  1. Align the matchmarks and install the tripod joint onto the front drive outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

    NOTICE:
    1. Do not tap the rollers.
    2. Keep the tripod joint free of foreign matter.



    F045046
  1. Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.

  1. Pack the front drive inboard joint assembly and front axle inboard boot with grease.

    Standard grease capacity:
    175 to 185 g (6.17 to 6.52 oz.)



    F045461E21
  1. Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark



11. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the front axle inboard joint boot to the front drive inboard joint assembly.



    C246251E01
  1. Check whether the drive shaft dimensions (A) are within the following specifications.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    Dimension (A):

    Dimension (A)
    LH Side
    576.9 mm (1.89 ft.)
    RH Side
    914.4 mm (3.00 ft.)



12. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.



    C205152
  1. for One Touch Type:

    1. Using a screwdriver, install the front axle inboard joint boot clamp.



    C215098E01
  1. for Claw Engagement Type:
    Text in Illustration 
    *a
    Claw

    1. Using needle nose pliers, install the front axle inboard joint boot clamp.

      NOTICE:
      Be careful not to damage the front axle inboard joint boot.



13. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
  1. Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.



    C205154
  1. for One Touch Type:

    1. Using a screwdriver, install front No. 2 axle inboard joint boot clamp.



    C215097E01
  1. for Claw Engagement Type:
    Text in Illustration 
    *a
    Claw

    1. Using needle nose pliers, install front No. 2 axle inboard joint boot clamp.

      NOTICE:
      Be careful not to damage the front axle inboard joint boot.



14. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new front drive shaft hole snap ring LH.

    NOTICE:
    Face the end gap of the front drive shaft hole snap ring downward.



15. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    C091598
  1. Check that there is no excessive play in the radial direction of the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no excessive play in the radial direction of the inboard joint.

  1. Check the boots for damage.



    C246251E01
  1. Check whether the drive shaft dimensions (A) are within the following specifications.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Keep the drive shaft assembly level during inspection.

    Dimension (A):

    Dimension (A)
    LH Side
    576.9 mm (1.89 ft.)
    RH Side
    914.4 mm (3.00 ft.)