Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Front Wiper Motor Circuit

for Preparation Click here


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly.

WIRING DIAGRAM


for LHD

E227682E04


for RHD

E227682E02


INSPECTION PROCEDURE

1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY


  1. for LHD:

    1. Remove the windshield wiper motor assembly (Click here).



    2. E144461E74
    3. Check low speed operation.
      Connect a auxiliary battery positive (+) lead to terminal B1-5 (+1) and a negative (-) lead to terminal B1-4 (E) and check that the motor operates at low speed.

      OK:
      Motor operates at low speed.

    4. Check high speed operation.
      Connect a auxiliary battery positive (+) lead to terminal B1-3 (+2) and a negative (-) lead to terminal B1-4 (E) and check that the motor operates at high speed.

      OK:
      Motor operates at high speed.

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Motor Assembly)



  1. for RHD:

    1. Remove the windshield wiper motor assembly (Click here).



    2. E144461E67
    3. Check low speed operation.
      Connect a auxiliary battery positive (+) lead to terminal B1-1 (+1) and a negative (-) lead to terminal B1-5 (E), and check that the motor operates at low speed.

      OK:
      Motor operates at low speed.

    4. Check high speed operation.
      Connect a auxiliary battery positive (+) lead to terminal B1-4 (+2) and a negative (-) lead to terminal B1-5 (E), and check that the motor operates at high speed.

      OK:
      Motor operates at high speed.

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Motor Assembly)



NG
REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)


  1. for LHD:



      E144463E28
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B1-2 (B) - Body ground
      Power switch on (IG)
      11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B1-4 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Windshield Wiper Motor Assembly)



  1. for RHD:



      E144463E24
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B1-2 (B) - Body ground
      Power switch on (IG)
      11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B1-5 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Windshield Wiper Motor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
  1. for LHD:

    1. Disconnect the I72 windshield wiper relay assembly connector and I32 windshield wiper switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B1-5 (+1) - I32-3 (+1)
      Always
      Below 1 Ω
      B1-5 (+1) - Body ground
      Always
      10 kΩ or higher
      B1-3 (+2) - I72-11 (+2)
      Always
      Below 1 Ω
      B1-3 (+2) - I32-4 (+2)
      Always
      Below 1 Ω
      B1-3 (+2) - Body ground
      Always
      10 kΩ or higher
      B1-1 (+S) - I72-1 (+SM)
      Always
      Below 1 Ω
      B1-1 (+S) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the I72 windshield wiper relay assembly connector and I32 windshield wiper switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B1-1 (+1) - I32-2 (+1)
      Always
      Below 1 Ω
      B1-1 (+1) - Body ground
      Always
      10 kΩ or higher
      B1-4 (+2) - I72-11 (+2)
      Always
      Below 1 Ω
      B1-4 (+2) - I32-1 (+2)
      Always
      Below 1 Ω
      B1-4 (+2) - Body ground
      Always
      10 kΩ or higher
      B1-3 (+S) - I72-1 (+SM)
      Always
      Below 1 Ω
      B1-3 (+S) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)