POWER SWITCH > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for LHD) |
| 5. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD) |
![]() |
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
| 6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD) |
![]() |
Remove the clip.
Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 8. REMOVE INSTRUMENT SIDE PANEL LH (for LHD) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 9. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD) |
![]() |
Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.
| 10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD) |
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
![]() |
Using a moulding remover, disengage the 4 clips and 2 guides.
for LHD:
![]() |
Disengage the 3 claws, 7 clips and 4 guides.
for RHD:
![]() |
Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.
Disconnect each connector.
![]() |
Remove the instrument cluster finish panel assembly as shown in the illustration.
| 11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Remove the 2 bolts <B>.
![]() |
Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.
| 13. REMOVE FRONT ASH RECEPTACLE ASSEMBLY (for LHD) |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the 2 clips as shown in the illustration.
Disconnect each connector to remove the front ash receptacle assembly.
| 14. REMOVE CONSOLE BOX ASSEMBLY (for LHD) |
| 15. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD) |
![]() |
Remove the 2 screws <C>.
![]() |
Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.
for LHD:
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
| 16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD) |
for LHD:
![]() |
Disengage the 3 clips and guide.
Disconnect the connector to remove the lower instrument panel finish panel assembly.
for RHD:
![]() |
Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.
| 17. REMOVE POWER SWITCH (for LHD) |
![]() |
Disengage the 2 claws and remove the power switch.
| 18. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD) |
| 19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD) |
| 20. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD) |
| 21. REMOVE INSTRUMENT SIDE PANEL RH (for RHD) |
![]() |
Using moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 22. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD) |
![]() |
Disengage the 2 claws and 4 clips as shown in the illustration.
Disconnect the connector to remove the upper instrument panel finish panel.
| 23. REMOVE POWER SWITCH (for RHD) |
![]() |
Disengage the 2 claws and remove the power switch.