Home › Engine / Hybrid System › 2AR-FXE STARTING › POWER SWITCH

POWER SWITCH > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for LHD)
(Click here)


5. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    B278978
  1. Remove the clip.

  1. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.



7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)


    B298720
  1. Disconnect the front door opening trim weatherstrip LH.



8. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)


    B280320
  1. Using a moulding remover, disengage the 4 claws as shown in the illustration.



    B280322
  1. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.



9. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for LHD)


    B280324
  1. Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.



10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)
  1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.



    B384402
  1. Using a moulding remover, disengage the 4 clips and 2 guides.



  1. for LHD:



      B386766
    1. Disengage the 3 claws, 7 clips and 4 guides.



  1. for RHD:



      B292377
    1. Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

  1. Disconnect each connector.



    B386767
  1. Remove the instrument cluster finish panel assembly as shown in the illustration.



11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD)


    B279865
  1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.



12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


    B384407
  1. Remove the 2 bolts <B>.



    B386777
  1. Disengage the 5 clips and 3 guides.

  1. Disconnect each connector to remove the instrument panel sub-assembly



13. REMOVE FRONT ASH RECEPTACLE ASSEMBLY (for LHD)


    B384412
  1. Remove the 2 screws <C>.



    B384413
  1. Disengage the 2 clips as shown in the illustration.

  1. Disconnect each connector to remove the front ash receptacle assembly.



14. REMOVE CONSOLE BOX ASSEMBLY (for LHD)
(Click here)


15. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)


    B281774
  1. Remove the 2 screws <C>.



    B281775
  1. Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.



  1. for LHD:



      B280290
    1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)


  1. for LHD:



      B293644
    1. Disengage the 3 clips and guide.

    2. Disconnect the connector to remove the lower instrument panel finish panel assembly.



  1. for RHD:



      B293673
    1. Disengage the 3 clips and guide to remove the lower instrument panel finish panel assembly.



17. REMOVE POWER SWITCH (for LHD)


    A259050
  1. Disengage the 2 claws and remove the power switch.



18. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure as for the LH side .



19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:
Use the same procedure as for the LH side .



20. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

HINT:
Use the same procedure as for the LH side.



21. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)


    B281763
  1. Using moulding remover, disengage the 4 claws as shown in the illustration.



    B281765
  1. Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.



22. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    B287390
  1. Disengage the 2 claws and 4 clips as shown in the illustration.

  1. Disconnect the connector to remove the upper instrument panel finish panel.



23. REMOVE POWER SWITCH (for RHD)


    A259048
  1. Disengage the 2 claws and remove the power switch.