HYBRID TRANSAXLE OIL SEAL > REPLACEMENT |
| 1. REMOVE FRONT WHEELS |
| 2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 3. REMOVE ENGINE UNDER COVER LH |
| 4. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 5. REMOVE ENGINE UNDER COVER RH |
| 6. REMOVE FRONT FENDER APRON SEAL LH |
| 7. REMOVE FRONT FENDER APRON SEAL RH |
| 8. DRAIN HYBRID TRANSAXLE FLUID |
![]() |
Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
| *1 | Filler Plug |
| *2 | Drain Plug |
Using a 10 mm hexagon socket wrench, remove the drain plug and gasket to drain the hybrid transaxle fluid.
Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket.
| 9. REMOVE FRONT AXLE SHAFT NUT |
![]() |
Using SST and a hammer, release the staked part of the front axle shaft nut.
While applying the brakes, remove the front axle shaft nut.
| 10. SEPARATE FRONT STABILIZER LINK ASSEMBLY |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
If the ball joint turns together with the nut, use a wrench to hold the stud bolt.
| 11. SEPARATE FRONT SPEED SENSOR |
![]() |
Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.
![]() |
Remove the bolt and front speed sensor from the steering knuckle.
| 12. SEPARATE TIE ROD ASSEMBLY |
![]() |
Remove the cotter pin and nut.
![]() |
Install SST to the tie rod assembly LH.
Secure SST using a string.
Using SST, separate the tie rod assembly LH from the steering knuckle.

| *1 | Center Nut | - | - |
| *a | String | *b | Grease Application Area |
![]() | Place the wrench here. | - | - |
| 13. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.
| 14. SEPARATE FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
| *a | Matchmark |
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.
| 15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the front drive shaft assembly LH.
| 16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.
Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.
Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.
| 17. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH |
![]() |
Using a screwdriver, remove the front drive shaft hole snap ring LH.
| 18. REMOVE DRIVE SHAFT BEARING BRACKET |
![]() |
Remove the 3 bolts and drive shaft bearing bracket.
| 19. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL |
Remove the left side oil seal.
![]() |
Using SST, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle transaxle assembly.
| *a | Hold |
| *b | Turn |
Remove the right side oil seal.
![]() |
Using SST, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle transaxle assembly.
| *a | Hold |
| *b | Turn |
| 20. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL |
Install a new left side oil seal.
![]() |
Using SST and a hammer, tap in a new hybrid vehicle transaxle assembly type T oil seal.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
Install a new RH side oil seal.
![]() |
Using SST and a hammer, tap in a new hybrid vehicle transaxle assembly type T oil seal.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
| 21. INSTALL DRIVE SHAFT BEARING BRACKET |
Install the drive shaft bearing bracket with the 3 bolts.
| 22. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new front drive shaft hole snap ring LH.
| 23. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
![]() |
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
![]() |
Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
| *a | Matchmark |
| 24. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
Install the front drive shaft assembly RH.
![]() |
Install the bearing bracket hole snap ring and a new bolt.
![]() |
Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
| *a | Matchmark |
| 25. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY |
Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
| 26. CONNECT TIE ROD ASSEMBLY |
Connect the tie rod assembly LH to the steering knuckle with the nut.
Install a new cotter pin.
| 27. INSTALL FRONT SPEED SENSOR |
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.
Install the front speed sensor to the steering knuckle with the bolt.
| 28. INSTALL FRONT STABILIZER LINK ASSEMBLY |
Install the front stabilizer link assembly to the front shock absorber assembly with the nut.
| 29. INSTALL FRONT AXLE SHAFT NUT |
Clean the threaded parts on the front drive shaft assembly and a new axle shaft nut using a non-residue solvent.
![]() |
Using a socket wrench (30 mm), install the front axle shaft nut.
Using a chisel and hammer, stake the front axle shaft nut.
| 30. ADD HYBRID TRANSAXLE FLUID |
![]() |
Add transaxle fluid until the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening.
| *1 | Filler Nozzle |
| *2 | Filler Plug |
After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)
| 31. INSPECT HYBRID TRANSAXLE FLUID |
![]() |
Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
| *1 | Filler Plug |
Check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)
Check for leaks if the quantity of transaxle fluid is low.
Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.
| 32. INSPECT FOR TRANSAXLE FLUID LEAK |
| 33. INSTALL FRONT WHEELS |
| 34. ADJUST FRONT WHEEL ALIGNMENT |
| 35. INSTALL FRONT FENDER APRON SEAL LH |
| 36. INSTALL FRONT FENDER APRON SEAL RH |
| 37. INSTALL ENGINE UNDER COVER LH |
| 38. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 39. INSTALL ENGINE UNDER COVER RH |
| 40. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 41. CHECK FOR SPEED SENSOR SIGNAL |