Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › HYBRID TRANSAXLE OIL SEAL

HYBRID TRANSAXLE OIL SEAL > REPLACEMENT

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT WHEELS


2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


3. REMOVE ENGINE UNDER COVER LH


4. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH


5. REMOVE ENGINE UNDER COVER RH


6. REMOVE FRONT FENDER APRON SEAL LH


7. REMOVE FRONT FENDER APRON SEAL RH


8. DRAIN HYBRID TRANSAXLE FLUID


    C243608E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug
    *2
    Drain Plug

  1. Using a 10 mm hexagon socket wrench, remove the drain plug and gasket to drain the hybrid transaxle fluid.

  1. Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



9. REMOVE FRONT AXLE SHAFT NUT


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle shaft nut.



10. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C238963
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.
    If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



11. SEPARATE FRONT SPEED SENSOR


    C238961
  1. Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.

    NOTICE:
    Be sure to separate the front speed sensor from the front shock absorber assembly completely.



    C238448
  1. Remove the bolt and front speed sensor from the steering knuckle.

    NOTICE:
    1. Prevent foreign matter from contacting the sensor tip.
    2. Be careful not to damage the front speed sensor.
    3. Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.



12. SEPARATE TIE ROD ASSEMBLY


    C238512
  1. Remove the cotter pin and nut.



    C238513E01
  1. Install SST to the tie rod assembly LH.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the lower ends of the tie rod assembly LH and SST are aligned.

  1. Secure SST using a string.

    NOTICE:
    Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



  1. Using SST, separate the tie rod assembly LH from the steering knuckle.


    C238514E02


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Grease Application Area
    V100136
    Place the wrench here.
    -
    -
    SST
    09960-20010   (09961-02010)

    CAUTION:
    Apply grease to the bolt threads and the tip of SST.

    NOTICE:
    1. Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



13. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY


    C238969
  1. Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.



14. SEPARATE FRONT DRIVE SHAFT ASSEMBLY


    C238968E01
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
    If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.



15. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C239400E01
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-00031  
    09520-01010  

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly LH.



16. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C239409
  1. Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. Do not drop the front drive shaft assembly RH.

  1. Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.



17. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    C057543
  1. Using a screwdriver, remove the front drive shaft hole snap ring LH.



18. REMOVE DRIVE SHAFT BEARING BRACKET


    A196633
  1. Remove the 3 bolts and drive shaft bearing bracket.



19. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL


  1. Remove the left side oil seal.



      C243614E01
    1. Using SST, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle transaxle assembly.

      SST
      09514-35011  
      Text in Illustration 
      *a
      Hold
      *b
      Turn



  1. Remove the right side oil seal.



      C243615E01
    1. Using SST, remove the hybrid vehicle transaxle assembly type T oil seal from the hybrid vehicle transaxle assembly.

      SST
      09612-30012  
      Text in Illustration 
      *a
      Hold
      *b
      Turn



20. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY TYPE T OIL SEAL


  1. Install a new left side oil seal.



      C243616E01
    1. Using SST and a hammer, tap in a new hybrid vehicle transaxle assembly type T oil seal.

      SST
      09223-15020  
      09950-70010   (09951-07150)

      Oil seal installation depth:
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    2. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.



  1. Install a new RH side oil seal.



      C243617E01
    1. Using SST and a hammer, tap in a new hybrid vehicle transaxle assembly type T oil seal.

      SST
      09710-30050  
      09950-70010   (09951-07150)

      Oil seal installation depth:
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    2. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.



21. INSTALL DRIVE SHAFT BEARING BRACKET
  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



22. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new front drive shaft hole snap ring LH.

    NOTICE:
    Face the end gap of the front drive shaft hole snap ring downward.



23. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the front drive inboard joint assembly with ATF.

  1. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.



    C165536
  1. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

    NOTICE:
    1. Face the end gap of the front drive shaft hole snap ring LH downward.
    2. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    3. Do not damage the front axle inboard joint boot.
    4. Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring LH.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



    C240136E01
  1. Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



24. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the front drive inboard joint assembly with ATF.

  1. Coat the lip of the hybrid vehicle transaxle assembly type T oil seal with MP grease.

  1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

  1. Install the front drive shaft assembly RH.

    NOTICE:
    1. Do not damage the hybrid vehicle transaxle assembly type T oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. When inserting the front drive shaft assembly RH, keep it level.



    C239409
  1. Install the bearing bracket hole snap ring and a new bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



    C240137E01
  1. Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



25. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
  1. Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }



26. CONNECT TIE ROD ASSEMBLY
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



27. INSTALL FRONT SPEED SENSOR
  1. Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

    HINT:
    Install the speed sensor harness bracket first and then the front flexible hose.

  1. Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.



28. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



29. INSTALL FRONT AXLE SHAFT NUT
  1. Clean the threaded parts on the front drive shaft assembly and a new axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work even when using a new drive shaft.
    2. Keep the threaded parts free of oil and foreign matter.



    C165538
  1. Using a socket wrench (30 mm), install the front axle shaft nut.

    Torque:
    294 N*m{ 2998 kgf*cm , 217 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle shaft nut.



30. ADD HYBRID TRANSAXLE FLUID


    C243609E01
  1. Add transaxle fluid until the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening.
    Text in Illustration 
    *1
    Filler Nozzle
    *2
    Filler Plug

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Use Toyota Genuine ATF WS.
    3. Be sure to fully insert the filler nozzle into the filler plug opening.
    4. Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.
    5. Be sure to directly check that the transaxle fluid level is within the specified range.
    6. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

    Reference:
    3.7 liters (3.9 US qts, 3.2 lmp.qts)

  1. After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    After adding fluid, make sure to check the fluid level.



31. INSPECT HYBRID TRANSAXLE FLUID


    C244536E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug

  1. Check that the fluid level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Be sure to directly check that the transaxle fluid level is within the specified range.
    3. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.
    4. If the fluid was replaced or fluid was added, make sure to recheck the fluid level after driving the vehicle.

  1. Check for leaks if the quantity of transaxle fluid is low.

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



32. INSPECT FOR TRANSAXLE FLUID LEAK


33. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



34. ADJUST FRONT WHEEL ALIGNMENT
(Click here)


35. INSTALL FRONT FENDER APRON SEAL LH


36. INSTALL FRONT FENDER APRON SEAL RH


37. INSTALL ENGINE UNDER COVER LH


38. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


39. INSTALL ENGINE UNDER COVER RH


40. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


41. CHECK FOR SPEED SENSOR SIGNAL
(Click here)