Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A82-123    Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF

for Preparation Click here


DESCRIPTION

  1. Refer to the circuit description for DTC P0A84-123 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A82
123
The speed of the battery cooling blower assembly is not within the specified range (1 trip detection)
  1. Battery cooling blower assembly
  2. Battery smart unit
  3. Power management control ECU
  4. No. 1 hybrid battery intake duct
  5. Wire harness or connector

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A84-123 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK FOR DTCS (HV)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.CHECK DUCT AND BLOWER


    A338265E01
  1. Check that the No. 1 hybrid battery intake duct and battery cooling blower assembly are not disconnected, damaged, or clogged with foreign matter, and that the acoustical materials have not peeled.

    OK:
    The duct and blower are not disconnected, damaged, or clogged with foreign matter and the acoustical materials have not peeled.

    Text in Illustration 
    *1
    No. 1 Hybrid Battery Intake Duct



NG
CORRECT THE PROBLEM
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - BATTERY SMART UNIT)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the luggage compartment front trim cover (Click here).

  1. Remove the rear side seatback assembly LH (Click here).

  1. Disconnect connector r1 from the battery cooling blower assembly.

  1. Disconnect connector N18 from the battery smart unit.



    A259921E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    r1-2 (FP0) - N18-5 (FP0)
    Power switch off
    Below 1 Ω
    r1-2 (FP0) or N18-5 (FP0) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    r1-2 (FP0) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified. Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery smart unit connector.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear side seatback assembly LH.

  1. Install the luggage compartment front trim cover.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the front luggage compartment trim cover (Click here).

  1. Disconnect connector r1 from the battery cooling blower assembly.

  1. Disconnect connector I3 from the power management control ECU (Click here).



    A333635E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    r1-3 (SI0) - I3-17 (SI0)
    Power switch off
    Below 1 Ω
    r1-3 (SI0) or I3-17 (SI0) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    r1-3 (SI0) - Body ground
    Power switch on (IG)
    Below 1 V

NOTICE:
Turning the power switch on (IG) with the battery cooling blower assembly connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the power management control ECU connector.

  1. Connect the battery cooling blower assembly connector.

  1. Install the front luggage compartment trim cover.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK)
  1. Remove the power management control ECU (Click here).



    A333634E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    I3-17 (SI0) - I3-5 (E01)
    10 kΩ or higher
    I3-17 (SI0) - I4-5 (E02)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Power Management Control ECU)

  1. Install the power management control ECU.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the luggage compartment front trim cover (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear the DTCs and freeze frame data (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the hybrid vehicle control ECU assembly sends a command to operate the battery cooling fan assembly.



    A244310E07
  1. While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    r1-2 (FP0) - r1-4 (GND0)
    Battery cooling blower assembly is operating

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    Result:
    Result
    Proceed to
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are 0 Hz.
    A
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are not 0 Hz.
    B

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the luggage compartment front trim cover.



B
Go to step 8
A


7.CHECK BATTERY SMART UNIT

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the luggage compartment front trim cover (Click here).

  1. Disconnect connector r1 from the battery cooling blower assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester (Click here).



    A342209E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    r1-2 (FP0) - r1-4 (GND0)
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery cooling blower assembly connector.

  1. Install luggage compartment front trim cover.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)  

8.CHECK BATTERY SMART UNIT (FREQUENCY)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the front luggage compartment trim cover (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check Frequency. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

  1. Enter the following menus: All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.



    A244310E01
  1. While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    r1-2 (FP0) - r1-4 (GND0)
    Battery cooling blower assembly is operating
    Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less.

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

NOTICE:
Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

HINT:
Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the front luggage compartment trim cover.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)