DTC P0A9C-123 Hybrid Battery Temperature Sensor "A" Range / Performance |
DTC P0AC6-123 Hybrid Battery Temperature Sensor "B" Range / Performance |
DTC P0ACB-123 Hybrid Battery Temperature Sensor "C" Range / Performance |
DTC P3065-123 Hybrid Battery Temperature Sensor Range/Performance Stuck "A" |
| DTC Title Sensor | Battery Temperature Sensor | Intelligent Tester Display |
| A | 0 | 1 |
| B | 1 | 2 |
| C | 2 | 3 |

| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A9C P0AC6 P0ACB P3065 | 123 | When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection) |
|

| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 is not output. | A |
| P0AFC-123 is also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Disconnect connectors z8 and N18 from the battery smart unit.
![]() |
Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).
| Tester Connection | Battery Temperature Sensor No. |
| z8-4 (TBO) - z8-10 (GBO) | 0 |
| z8-3 (TB1) - z8-9 (GB1) | 1 |
| z8-2 (TB2) - z8-8 (GB2) | 2 |
| Thermistor Temperature | Switch Condition | Specified Condition |
| 0 °C (32 °F) | Power switch off | 26.7 to 27.8 kΩ |
| 25 °C (77 °F) | Power switch off | 9.9 to 10.1 kΩ |
| 40 °C (104 °F) | Power switch off | 5.73 to 5.92 kΩ |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Standard Resistance |
| z8-4 (TBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-4 (TBO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-10 (GBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-10 (GBO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-3 (TB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-3 (TB1) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-9 (GB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-9 (GB1) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-2 (TB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-2 (TB2) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-8 (GB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-8 (GB2) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-1 (TCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-1 (TCO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-7 (GCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-7 (GCO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
Connect the battery smart unit connectors.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||