DTC P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low |
DTC P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low |
DTC P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low |
DTC P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low |
DTC P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low |
DTC P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low |
DTC P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low |
DTC P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low |
DTC P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low |
DTC P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low |
DTC P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low |
DTC P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low |
DTC P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low |
DTC P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low |
DTC P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low |
DTC P0B88-123 Hybrid Battery Voltage Sensor "P" Circuit Low |
DTC P0B8D-123 Hybrid Battery Voltage Sensor "Q" Circuit Low |
DTC P0B92-123 Hybrid Battery Voltage Sensor "R" Circuit Low |
DTC P308A-123 Hybrid Battery Voltage Sensor All Circuits Low |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0B3D P0B42 P0B47 P0B4C P0B51 P0B56 P0B5B P0B60 P0B65 P0B6A P0B6F P0B74 P0B79 P0B7E P0B83 P0B88 P0B8D P0B92 P308A | 123 | Each battery block voltage becomes less than 2.5 V (open) (1 trip detection) |
|
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 or P0A95-123 is not output. | A |
| P0AFC-123 or P0A95-123 is also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.CHECK CONNECTOR CONNECTION CONDITION |
Check that the service plug grip is not installed.
Remove the No. 2 hybrid vehicle battery shield panel .
![]() |
Check the connections of the z7 connector of the battery smart unit.
Install the No. 2 hybrid vehicle battery shield panel.
|
| ||||
| OK | |
| 3.REPLACE BATTERY SMART UNIT |
| NEXT | |
| 4.CLEAR DTC (HV) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Clear the DTCs and freeze frame data (Click here).
Perform a road test to charge and discharge the HV battery.
Disconnect the intelligent tester from the DLC3.
| NEXT | |
| 5.RECONFIRM DTC OUTPUT (HV) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are not output | A |
| Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are output | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | ||
| ||