DTC P0AAE-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit Low |
DTC P0AAF-123 Hybrid Battery Pack Air Temperature Sensor "A" Circuit High |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0AAE P0AAF | 123 | When the temperature indicated by the inlet air temperature sensor is lower than a predetermined limit (open circuit) or is higher than a predetermined limit (short circuit) |
|
| Displayed Temperature | Malfunction |
| -45 °C (-49 °F) or less | Open or +B short circuit |
| 95 °C (203 °F) or more | GND short |
| 1.CHECK FOR DTCS (HV) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 is not output. | A |
| P0AFC-123 is also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Check installation of inlet air temperature sensor.
![]() |
Check the connections of the z8 connector of the battery smart unit.
| Result | Proceed to |
| NG | B |
| OK | Go to next step |
![]() |
Visually check the installation condition of the inlet air temperature sensor.
| Result | Proceed to |
| The inlet air temperature sensor is installed in the correct location and its claws are engaged securely | A |
| Claws are damaged. | C |
| Inlet air temperature sensor is not installed correctly, but claws are not damaged. | D |
Install the front luggage compartment trim cover.
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Remove the rear side seat back assembly LH.
Disconnect connectors N18 and z8 from the battery smart unit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z8-1 (TCO) - z8-7 (GCO) | 0 °C (32 °F) | 26.7 to 27.8 kΩ |
| 25 °C (77 °F) | 9.9 to 10.1 kΩ | |
| 40 °C (104 °F) | 5.73 to 5.92 kΩ |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z8-1 (TCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-1 (TCO) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-7 (GCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-7 (GCO) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z8-4 (TBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-4 (TBO) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-10 (GBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-10 (GBO) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-3 (TB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-3 (TB1) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-9 (GB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-9 (GB1) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-2 (TB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-2 (TB2) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
| z8-8 (GB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or higher |
| z8-8 (GB2) - N18-6 (GND) | Power switch off | 10 kΩ or higher |
Connect the battery smart unit connectors.
Install the rear side seat back assembly LH.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (INLET AIR TEMPERATURE SENSOR AND BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Check the wire harness and connectors of the battery temperature sensor and inlet air temperature sensor for abnormalities by sight and touch.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||