DTC U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| U029A | 123 | Problem in serial communication between the battery smart unit and power management control ECU (1 trip detection) |
|

| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check for DTCs (Click here).
| Result | Proceed to |
| Only U029A-123 is output. | A |
| DTCs other than U029A-123 are also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.CHECK BATTERY SMART UNIT (IGCT VOLTAGE)) |
Check that the service plug grip is not installed.
Remove the rear side seat back assembly LH (Click here).
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N18-3 (IGCT) - N18-6 (GND) | Power switch on (IG) | 11 to 14 V |
| *a | Component with harness connected (Battery Smart Unit) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the rear side seat back assembly LH.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT) |
Check that the service plug grip is not installed.
Disconnect connector I3 from the power management control ECU (Click here).
Remove the rear side seatback assembly LH (Click here).
Disconnect connector N18 from the battery smart unit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I3-30 (BTH+) - N18-1 (BTH+) | Power switch off | Below 1 Ω |
| I3-29 (BTH-) - N18-4 (BTH-) | Power switch off | Below 1 Ω |
| N18-1 (BTH+) - N18-6 (GND) and body ground | Power switch off | 10 kΩ or higher |
| N18-4 (BTH-) - N18-6 (GND) and body ground | Power switch off | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
| *b | Rear view of wire harness connector (to Battery Smart Unit) |
![]() |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT fuse |
![]() |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 fuse |
![]() |
Remove the ECU-IG2 No. 1 fuse from the instrument panel junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 fuse |
Disconnect all connectors from the power management control ECU.
Measure the resistance according to the value(s) in the table below.

| *a | Rear view of wire harness connector (to Power Management Control ECU) | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| I3-30 (BTH+) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A38-1 (+B2) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A39-3 (+B1) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A38-4 (MREL) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - I3-16 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-30 (BTH+) - A38-19 (GI) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A38-1 (+B2) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A39-3 (+B1) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A38-4 (MREL) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - I3-16 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-29 (BTH-) - A38-19 (GI) | Power switch off | 10 kΩ or higher |
Connect the battery smart unit connector.
Install the rear side seatback assembly LH.
Connect the power management control ECU connectors.
|
| ||||
| OK | |
| 4.CHECK POWER MANAGEMENT CONTROL ECU |
Check that the service plug grip is not installed.
Remove the rear side seatback assembly LH (Click here).
Disconnect connector N18 from the battery smart unit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N18-1 (BTH+) - N18-6 (GND) | Power switch on (IG) | 2.3 to 2.7 V |
| N18-4 (BTH-) - N18-6 (GND) | Power switch on (IG) | 2.3 to 2.7 V |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| N18-1 (BTH+) - N18-4 (BTH-) | Power switch off | 4.4 to 5.4 kΩ |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
Connect the battery smart unit connector.
Install the rear side seatback assembly LH.
|
| ||||
| OK | ||
| ||