Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › WATER PUMP WITH MOTOR

WATER PUMP WITH MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP WITH MOTOR ASSEMBLY


    A259441E01
  1. Connect the water hose.
    Text in Illustration 
    *a
    Rib
    *b
    Alignment Mark
    *c
    90°
    *d
    2 to 7 mm (0.0787 to 0.276 in.)

    NOTICE:
    1. Make sure that the clip is positioned as shown in the illustration
    2. Make sure to align the alignment marks of the hoses with the ribs of the inverter water pump assembly.
    3. Do not remove the pieces of cloth or plastic bags from the pipe and disconnected hose until installation.

  1. Install the water pump with motor assembly with the 3 bolts.

    Torque:
    6.1 N*m{ 62 kgf*cm , 54 in.*lbf }

    NOTICE:
    Do not hold the water pump with motor assembly by the connector terminals when removing or installing it.

  1. Connect the connector.



    A259440E01
  1. Connect the water hose.
    Text in Illustration 
    *a
    Rib
    *b
    Alignment Mark
    *c
    220°
    *d
    2 to 7 mm (0.0787 to 0.276 in.)

    NOTICE:
    1. Make sure that the clip is positioned as shown in the illustration
    2. Make sure to align the alignment marks of the hoses with the ribs of the inverter water pump assembly.
    3. Do not remove the pieces of cloth or plastic bags from the pipe and disconnected hose until installation.



2. INSTALL INVERTER RESERVE TANK ASSEMBLY
  1. Temporarily install the inverter reserve tank assembly with the 2 bolts.



    A259438E01
  1. Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. ADD COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign objects.
  2. If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be set.

    DTC Code
    Detection Item
    P0A01-725
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A01-726
    Motor Electronics Coolant Temperature Sensor Circuit Intermittent
    P0A08-264
    DC / DC Converter Status Circuit
    P0A78-284
    Drive Motor "A" Inverter Performance
    P0A78-286
    Drive Motor "A" Inverter Performance
    P0A7A-322
    Generator Inverter Performance
    P0A7A-324
    Generator Inverter Performance
    P0A93-346
    Inverter Cooling System Performance
    P0A94-553
    DC / DC Converter Performance
    P0A94-557
    DC / DC Converter Performance
    P0AEE-276
    Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
    P0AEE-277
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P0BD0-314
    Generator Inverter Temperature Sensor Circuit Range / Erratic
    P0BCD-315
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P0C3C-625
    DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
    P0C39-626
    DC / DC Converter Temperature Sensor "A" Range / Performance
    P0C41-627
    DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
    P0C3E-628
    DC / DC Converter Temperature Sensor "B" Range / Performance
    P0C73-776
    Motor Electronics Coolant Pump "A" Control Performance



    A258733
  1. Slowly pour coolant into the reserve tank until it reaches the FULL line.

    Coolant quantity:
    3.2 liters (3.4 US qts, 2.8 Imp. qts.)

    NOTICE:
    To prevent foreign matter such as dust or dirt from entering the cooling system, make sure to confirm that the container used to add coolant is clean and free of foreign matter such as dust or dirt.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

    4. Keep the coolant at the FULL line in the reserve tank to compensate for the drop in coolant level when the air bleeds.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      1. If free spinning of the inverter water pump is detected for approximately 5 seconds, failsafe control will be activated to suspend the operation of the pump for approximately 15 seconds and resume operation for approximately 4 seconds repeatedly. Operation of the inverter water pump will return to normal if coolant is added.
      2. Loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. When not using the intelligent tester:

    1. Turn the power switch on (READY).[*1]

    2. Turn the power switch off and add coolant to the FULL line because the coolant level drops as the air bleeds.[*2]

      NOTICE:
      1. Be sure to turn the power switch off before adding SLLC.
      2. Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

    3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. After the air is completely bled from the cooling system, tighten the reserve tank cap.



    A258733
  1. Add coolant to the FULL line of the reserve tank.



4. INSPECT FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A258731
  1. Install the radiator cap tester.

  1. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

  1. Reinstall the reserve tank cap.