Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

POWER STEERING SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
  2. Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.

  1. Turn the power switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the intelligent tester on.

  5. Check the freeze frame data on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Meter Vehicle Velocity
    Vehicle speed from meter/
    Min.: 0.0 km/h (0.0 mph)
    Max.: 300.0 km/h (186.4 mph)
    0 km/h (0 mph)
    Power switch on (READY) and vehicle stopped
    No significant fluctuation
    Power switch on (READY) and vehicle driven at a constant speed
    Engine Revolution
    Engine speed/
    Min.: 0 rpm
    Max.: 12800 rpm
    No significant fluctuation
    Power switch on (READY) at a constant speed
    Motor Actual Current
    Amount of current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    The value rises
    Power switch on (READY) and steering wheel being turned
    Command Value Current
    Requested current to motor/
    Min.: -327.68 A
    Max.: 327.67 A
    Value changes in proportion to steering effort
    -The value increases when turning left and decreases when turning right
    Power switch on (READY) and steering wheel being turned
    Steering Angle Velocity
    Steering angle speed/
    Min.: -32768 deg/s
    Max.: 32767 deg/s
    Value changes in proportion to steering speed
    -The value increases when turning left and decreases when turning right
    Power switch on (READY) and steering wheel being turned
    Thermistor Temperature
    ECU substrate temperature/
    Min.: -40.0°C (-40.0°F)
    Max.: 150.0°C (302.0°F)
    -40°C to 150°C (-40°F to 302°F)
    Power switch on (READY)
    PIG Power Supply
    Power source voltage to active motor/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Power switch on (READY) and steering wheel being turned
    IG Power Supply
    ECU power source voltage/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Power switch on (IG)
    Steering Wheel Torque
    Steering wheel torque/
    Min.: -327.68 Nm
    Max.: 7.00 Nm
    Value changes in proportion to steering effort
    -The value increases when turning left and decreases when turning right
    Power switch on (READY) and steering wheel being turned
    Motor Rotation Angle
    Motor rotation angle/
    Min.: 0.000 deg
    Max.: 1441.770 deg
    During steering operation, motor rotation angle value changes from 0 to 360°
    Power switch on (READY) and steering wheel being turned
    Motor Voltage
    Motor power supply voltage/
    Min.: 0.000 V
    Max.: 98.000 V
    9 to 16 V
    Power switch on (READY) and steering wheel being turned
    Motor Terminal Volt (U)
    Motor terminal voltage (A phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned
    Motor Terminal Volt (V)
    Motor terminal voltage (B phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned
    Motor Terminal Volt (W)
    Motor terminal voltage (C phase)/
    Min.: 0.000 V
    Max.: 98.000 V
    Value changes within 4 to 35 V range
    Power switch on (READY) and steering wheel being turned
    Torque Sensor 1 Output
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (READY) and steering wheel not being turned (without load)
    2.5 to 4.7 V
    Power switch on (READY) and steering wheel being turned to the right with vehicle stopped
    0.3 to 2.5 V
    Power switch on (READY) and steering wheel being turned to the left with vehicle stopped
    Torque Sensor 2 Output
    Torque sensor voltage/
    Min.: 0.0000 V
    Max.: 4.9725 V
    2.3 to 2.7 V
    Power switch on (READY) and steering wheel not being turned (without load)
    0.3 to 2.5 V
    Power switch on (READY) and steering wheel being turned to the right with vehicle stopped
    2.5 to 4.7 V
    Power switch on (READY) and steering wheel being turned to the left with vehicle stopped
    Battery Voltage
    Auxiliary battery voltage/
    Min.: 0.0 V
    Max.: 25.5 V
    9 to 16 V
    Power switch on (IG)
    PS Assist Signal
    Power steering assist signal/
    ON or OFF
    OFF
    Power switch on (IG)
    ON
    Power switch on (READY)
    Ready Status
    Ready status/
    Ready or OFF
    Ready or OFF
    -