CONDENSER > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM |
Turn the power switch on (READY).
Turn the A/C switch on.
Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.
Turn the power switch off.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
| 3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 5. REMOVE FRONT BUMPER ASSEMBLY |
| 6. REMOVE FRONT BUMPER ENERGY ABSORBER |
![]() |
Disengage the 2 guides to remove the front bumper energy absorber.
| 7. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
![]() |
Disengage the 5 clamps.
Remove the 6 bolts and front bumper reinforcement sub-assembly.
| 8. REMOVE INLET AIR CLEANER ASSEMBLY |
![]() |
Remove the 2 bolts and inlet air cleaner assembly.
| 9. REMOVE HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 10. REMOVE HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 11. REMOVE NO. 5 INVERTER BRACKET |
![]() |
Remove the 2 bolts and No. 5 inverter bracket.
| 12. REMOVE UPPER RADIATOR SUPPORT |
![]() |
Disconnect the 2 connectors.
![]() |
Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.
| *a | for RHD: |
| *b | for LHD: |
Remove the 2 radiator support cushions.
| 13. REMOVE RADIATOR SIDE DEFLECTOR RH |
![]() |
Disengage the 3 claws and remove the radiator side deflector RH.
| 14. REMOVE RADIATOR SIDE DEFLECTOR LH |
![]() |
Disengage the 3 claws and guide, and remove the radiator side deflector LH.
| 15. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the cooler condenser assembly.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
| 16. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
![]() |
Remove the bolt and disconnect the air conditioner tube and accessory assembly from the cooler condenser assembly.
Remove the O-ring from the air conditioner tube and accessory assembly.
| 17. REMOVE COOLER CONDENSER ASSEMBLY |
![]() |
Remove the 4 bolts.
![]() |
Pull the radiator assembly in the direction indicated by the arrow.
![]() |
Remove the 2 bolts.
![]() |
Remove the cooler condenser assembly as shown in the illustration.