DTC P0A9D-123 Hybrid Battery Temperature Sensor "A" Circuit Low |
DTC P0A9E-123 Hybrid Battery Temperature Sensor "A" Circuit High |
DTC P0AC7-123 Hybrid Battery Temperature Sensor "B" Circuit Low |
DTC P0AC8-123 Hybrid Battery Temperature Sensor "B" Circuit High |
DTC P0ACC-123 Hybrid Battery Temperature Sensor "C" Circuit Low |
DTC P0ACD-123 Hybrid Battery Temperature Sensor "C" Circuit High |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A9D P0A9E P0AC7 P0AC8 P0ACC P0ACD | 123 | When the temperature of the battery temperature sensor is less than the standard value (open) or higher than the standard value (shorted) (1 trip detection). |
|
| Temperature Displayed | Malfunction |
| Below -45°C (-49°F) | Open or +B short circuit |
| 95°C (203°F) or more | GND short circuit |
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 is not output. | A |
| P0AFC-123 is also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Temp of Batt TB 1 to 3.
Turn the power switch off.
| NEXT | |
| 3.CHECK CONNECTOR CONNECTION CONDITION |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
![]() |
Check the connections of the z8 connector of the battery smart unit.
Install the front luggage compartment trim cover.
|
| ||||
| OK | |
| 4.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Disconnect connectors z8 and N18 from the battery smart unit.
![]() |
Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).
| Tester Connection | Battery Temperature Sensor No. |
| z8-4 (TBO) - z8-10 (GBO) | 0 |
| z8-3 (TB1) - z8-9 (GB1) | 1 |
| z8-2 (TB2) - z8-8 (GB2) | 2 |
| Thermistor Temperature | Switch Condition | Specified Condition |
| 0 °C (32 °F) | Power switch off | 26.7 to 27.8 kΩ |
| 25 °C (77 °F) | Power switch off | 9.9 to 10.1 kΩ |
| 40 °C (104 °F) | Power switch off | 5.73 to 5.92 kΩ |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Standard Resistance |
| z8-4 (TBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-4 (TBO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-10 (GBO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-10 (GBO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-3 (TB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-3 (TB1) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-9 (GB1) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-9 (GB1) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-2 (TB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-2 (TB2) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-8 (GB2) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-8 (GB2) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-1 (TCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-1 (TCO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| z8-7 (GCO) - N18-3 (IGCT) | Power switch off | 10 kΩ or more |
| z8-7 (GCO) - N18-6 (GND) | Power switch off | 10 kΩ or more |
| *a | Rear view of wire harness connector (to Battery Smart Unit) |
Connect the battery smart unit connectors.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR) |
Check that the service plug grip is not installed.
Remove the front luggage compartment trim cover (Click here).
Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.
Install the front luggage compartment trim cover.
|
| ||||
| OK | ||
| ||