Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

DTC    B1242    Wireless Door Lock Tuner Circuit Malfunction

for Preparation Click here


DESCRIPTION

The door control receiver is used to receive radio waves relating to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No.
DTC Detection Condition
Trouble Area
B1242
  1. Short in RDAM to ground between the certification ECU (smart key ECU assembly) and the door control receiver.
  2. Short in RDAM to ground when RCO (5 V) output from the ECU is off.
  1. Wire harness or connector
  2. Door control receiver
  3. Certification ECU (Smart key ECU assembly)

WIRING DIAGRAM


B282114E30


INSPECTION PROCEDURE

NOTICE:
  1. When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system (Click here).
  3. When replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the Service Bulletin.
  4. This DTC is not detected within 10 seconds after the power switch turned to off from on (IG).

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    B281165E05
  1. Disconnect the O43 door control receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (+5) - O43-1 (GND)
    Power switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V
    (Pulse generation)
    O43-5 (DATA) - O43-1 (GND)
    Power switch off
    11 to 14 V pulse generation at regular intervals

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O43-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (Door control receiver)



NG
Go to step 2
OK

REPLACE DOOR CONTROL RECEIVER (Click here)  

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the O2 and I86 certification ECU (smart key ECU assembly) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O2-7 (CSEL) - O43-2 (CSEL)
    Always
    Below 1 Ω
    O2-6 (RDAM) - O43-5 (DATA)
    Always
    Below 1 Ω
    O2-15 (RCO) - O43-4 (+5)
    Always
    Below 1 Ω
    I86-1 (E) - Body ground
    Always
    Below 1 Ω
    O43-1 (GND) - Body ground
    Always
    Below 1 Ω
    O2-7 (CSEL) or O43-2 (CSEL) - Body ground
    Always
    10 kΩ or higher
    O2-6 (RDAM) or O43-5 (DATA) - Body ground
    Always
    10 kΩ or higher
    O2-15 (RCO) or O43-4 (+5) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)