DTC P0516-769 Battery Temperature Sensor Circuit Low |
DTC P0517-770 Battery Temperature Sensor Circuit High |
| Terminal | THB (with Connector Disconnected) | Resistance | Ambient Temperature |
| THB - E2 | 4.5 to 5.5 V | 3.00 to 3.73 kΩ | Approximately 10°C (50°F) |
| 1.60 to 1.80 kΩ | Approximately 25°C (77°F) | ||
| 0.80 to 1.00 kΩ | Approximately 40°C (104°F) |

| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0516 | 769 | Malfunction in the thermistor assembly circuit (short to GND) |
|
| P0517 | 770 | Malfunction in the thermistor assembly circuit (open or short to +B) |

| Displayed Temperature | Malfunction |
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to GND |
| 1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
Read the Data List.
| Result | Proceed to |
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN) |
![]() |
Disconnect connector O26 from the thermistor assembly.
![]() |
Connect terminals 2 (THB) and 1 (E2) of vehicle side connector O26 of the thermistor assembly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
Read the Data List.
| Tester Display | Condition | Specified Condition |
| Auxiliary Batt Temperature | Terminals THB and E2 connected. Power switch on (IG) | 215°C (419°F) |
| *a | Front view of wire harness connector (to Thermistor Assembly) |
Turn the power switch off.
Connect the thermistor assembly connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - THERMISTOR ASSEMBLY) |
![]() |
Connect terminals 28 (THB) and 30 (ETHB) of connector I3 of the power management control ECU.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
Read the Data List.
| Tester Display | Condition | Specified Condition |
| Auxiliary Batt Temperature | Terminals THB and ETHB connected. Power switch on (IG) | 215°C (419°F) |
| *a | Component with harness connected (Power Management Control ECU) |
Turn the power switch off.
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT) |
![]() |
Disconnect connector O26 from the thermistor assembly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
Read the Data List.
| Tester Display | Switch Condition | Specified Condition |
| Auxiliary Batt Temperature | Power switch on (IG) | -40°C (-40°F) |
Turn the power switch off.
Connect the thermistor assembly connector.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - POWER MANAGEMENT CONTROL ECU) |
Disconnect connector O26 from the thermistor assembly.
![]() |
Disconnect connector I3 from the power management control ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O26-2 (THB) - I3-28 (THB) | Power switch off | Below 1 Ω |
| O26-1 (E2) - I3-30 (ETHB) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| O26-2 (THB) or I3-28 (THB)- Body ground and other terminals | Power switch off | 10 kΩ or higher |
| O26-1 (E2) or I3-30 (ETHB)- Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Thermistor Assembly) |
| *b | Rear view of wire harness connector (to Power Management Control ECU) |
Connect the thermistor assembly connector.
Connect the power management control ECU connector.
|
| ||||
| OK | ||
| ||