Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A1B-505    Drive Motor "A" Control Module

DTC    P0A1B-806    Drive Motor "A" Control Module

for Preparation Click here


DESCRIPTION

For a description of the inverter .
If the motor inverter overheats, has a circuit malfunction, or has an internal short, the inverter transmits this information to the MG ECU via the motor inverter fail signal line. If an abnormal amount of current flows through the motor inverter, the MG ECU detects it and sends a signal to inform the power management control ECU of the malfunction.

HINT:
The term "drive motor A" indicates MG2.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A1B
505
Motor inverter fail signal detection (overcurrent due to MG ECU malfunction)
Inverter with converter assembly
806
Abnormal MG2 current value detection (MG ECU malfunction)

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0A78-202 is not output.
    A
    P0A78-202 is also output.
    B

    NOTICE:
    1. If P0A78-202 is output, troubleshoot it first. After completing the troubleshooting for P0A78-202, return to perform troubleshooting for this DTC.
    2. Parts repaired or replaced during troubleshooting for P0A78-202 do not need to be re-inspected in this diagnosis procedure.

  1. Turn the power switch off.



B
GO TO DTC CHART (P0A78-202) (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    HINT:
    1. If P0A78-202 was not output in step 1 of this diagnosis procedure, check Table 1 below.
    2. If P0A78-202 was output in step 1 of this diagnosis procedure, repair that DTC first, then check Table 2 below.

    Result:
    Result
    Proceed to
    P0A1B-505 or 806 only is output, or DTCs except the ones in the tables below are also output.
    A
    Any of the following DTCs are also output.
    B


    Table 1 
    DTC No.
    Relevant Diagnosis
    P06B0-163
    Sensor Power Supply "A" Circuit / Open
    P06D6-511
    Sensor Reference Voltage "F" Circuit / Open
    P06E6-164
    Sensor Power Supply "C" Circuit / Open
    P0A1A-151, 166, 658, 791
    Generator Control Module
    P0A1B-198, 786, 794
    Drive Motor "A" Control Module
    P0A1D (all INF codes)*1
    Hybrid Powertrain Control Module
    P0A3F-243
    Drive Motor "A" Position Sensor Circuit
    P0A40-500
    Drive Motor "A" Position Sensor Circuit Range / Performance
    P0A41-245
    Drive Motor "A" Position Sensor Circuit Low
    P0A4B-253
    Generator Position Sensor Circuit
    P0A4C-513
    Generator Position Sensor Circuit Range / Performance
    P0A4D-255
    Generator Position Sensor Circuit Low
    P0BEA-290
    Drive Motor "A" Phase V Current Sensor Circuit Range / Performance
    P0BEE-298
    Drive Motor "A" Phase W Current Sensor Circuit Range / Performance
    P0C76-523
    Hybrid Battery System Discharge Time Too Long
    P0D2E-586
    Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance
    P0D2F-266
    Drive Motor "A" Inverter Voltage Sensor Circuit Low
    P0D30-267
    Drive Motor "A" Inverter Voltage Sensor Circuit High
    P0E05-328
    Generator Phase V Current Sensor Circuit Range / Performance
    P0E09-336
    Generator Phase W Current Sensor Circuit Range / Performance
    P0E32-585
    DC/DC Converter Voltage Sensor "A" Range / Performance
    P0E33-589
    DC/DC Converter Voltage Sensor "A" Low
    P0E34-590
    DC/DC Converter Voltage Sensor "A" High
    P1C2A-155
    Generator A/D Converter Circuit
    P1C2B-192
    Drive Motor "A" A/D Converter Circuit
    P1C2D-587
    Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
    P1C3C-294
    Drive Motor "A" Phase V Current Sensor Correlation
    P1C3D-302
    Drive Motor "A" Phase W Current Sensor Correlation
    P1C3E-333
    Generator Phase V Current Sensor Correlation
    P1C3F-341
    Generator Phase W Current Sensor Correlation
    P1C4A-288
    Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance
    P1C4F-296
    Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance
    P1C54-326
    Generator Phase V Current Sensor Sub Circuit Range / Performance
    P1C59-334
    Generator Phase W Current Sensor Sub Circuit Range / Performance
    P1C6D-501
    Drive Motor "A" Phase V Current Sensor Offset Range / Performance
    P1C6E-502
    Drive Motor "A" Phase W Current Sensor Offset Range / Performance
    P1C71-515
    Generator Phase V Current Sensor Offset Range / Performance
    P1C72-516
    Generator Phase W Current Sensor Offset Range / Performance
    P1C73-512
    Sensor Standard Voltage "F" Circuit / Open
    P1CA6-156
    Generator Control Module Malfunction
    P1CA7-193
    Drive Motor Control Module Malfunction
    P1CAC-200
    Generator Position Sensor Angle Malfunction
    P1CAD-168
    Drive Motor "A" Position Sensor Angle Malfunction
    P1CAF-792
    Generator Position Sensor REF Signal Cycle Malfunction
    P1CB0-795
    Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
    P1CB2-793
    Generator Position Sensor REF Signal Stop Malfunction
    P1CB3-796
    Drive Motor "A" Position Sensor REF Signal Stop Malfunction
    P3133-659
    Communication Error from Generator to Drive Motor "A"
    P3134-661
    Communication Error from Drive Motor "A" to Generator

    Table 2 
    DTC No.
    Relevant Diagnosis
    P06B0-163
    Sensor Power Supply "A" Circuit / Open
    P06D6-511
    Sensor Reference Voltage "F" Circuit / Open
    P06E6-164
    Sensor Power Supply "C" Circuit / Open
    P0A1A-151, 166, 658, 791
    Generator Control Module
    P0A1B-198, 786, 794
    Drive Motor "A" Control Module
    P0A1D (all INF codes)*1
    Hybrid Powertrain Control Module
    P0A3F-243
    Drive Motor "A" Position Sensor Circuit
    P0A40-500
    Drive Motor "A" Position Sensor Circuit Range / Performance
    P0A41-245
    Drive Motor "A" Position Sensor Circuit Low
    P0A4B-253
    Generator Position Sensor Circuit
    P0A4C-513
    Generator Position Sensor Circuit Range / Performance
    P0A4D-255
    Generator Position Sensor Circuit Low
    P0C76-523
    Hybrid Battery System Discharge Time Too Long
    P0D2E-586
    Drive Motor "A" Inverter Voltage Sensor Circuit Range / Performance
    P0D2F-266
    Drive Motor "A" Inverter Voltage Sensor Circuit Low
    P0D30-267
    Drive Motor "A" Inverter Voltage Sensor Circuit High
    P0E05-328
    Generator Phase V Current Sensor Circuit Range / Performance
    P0E09-336
    Generator Phase W Current Sensor Circuit Range / Performance
    P0E32-585
    DC/DC Converter Voltage Sensor "A" Range / Performance
    P0E33-589
    DC/DC Converter Voltage Sensor "A" Low
    P0E34-590
    DC/DC Converter Voltage Sensor "A" High
    P1C2A-155
    Generator A/D Converter Circuit
    P1C2B-192
    Drive Motor "A" A/D Converter Circuit
    P1C2D-587
    Hybrid Battery Voltage / DC/DC Converter Voltage Correlation
    P1C3C-294
    Drive Motor "A" Phase V Current Sensor Correlation
    P1C3D-302
    Drive Motor "A" Phase W Current Sensor Correlation
    P1C3E-333
    Generator Phase V Current Sensor Correlation
    P1C3F-341
    Generator Phase W Current Sensor Correlation
    P1C54-326
    Generator Phase V Current Sensor Sub Circuit Range / Performance
    P1C59-334
    Generator Phase W Current Sensor Sub Circuit Range / Performance
    P1C71-515
    Generator Phase V Current Sensor Offset Range / Performance
    P1C72-516
    Generator Phase W Current Sensor Offset Range / Performance
    P1C73-512
    Sensor Standard Voltage "F" Circuit / Open
    P1CA6-156
    Generator Control Module Malfunction
    P1CA7-193
    Drive Motor Control Module Malfunction
    P1CAC-200
    Generator Position Sensor Angle Malfunction
    P1CAD-168
    Drive Motor "A" Position Sensor Angle Malfunction
    P1CAF-792
    Generator Position Sensor REF Signal Cycle Malfunction
    P1CB0-795
    Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
    P1CB2-793
    Generator Position Sensor REF Signal Stop Malfunction
    P1CB3-796
    Drive Motor "A" Position Sensor REF Signal Stop Malfunction
    P3133-659
    Communication Error from Generator to Drive Motor "A"
    P3134-661
    Communication Error from Drive Motor "A" to Generator

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0A1B-505 or P0A1B-806 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A

REPLACE INVERTER WITH CONVERTER ASSEMBLY (Click here)