ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch*9 | Power switch status / ON or OFF | ON: Power switch on (IG) OFF: Power switch off | Use this Data List item to help determine the cause when all the smart entry and start system/wireless functions do not operate. |
| #Codes | Number of trouble codes / Min: 0, Max: 255 | Number of stored DTCs displayed | - |
| Immobilizer when IG=ON | Engine immobiliser system status when power switch on (IG) / SET or UNSET | SET: Engine immobiliser system set (driver door open and closed with power switch on (IG)) UNSET: Engine immobiliser system not set with power switch on (IG) or engine immobiliser system unset for 40 times after engine immobiliser system set | - |
| Immobiliser*9 | Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset | Set: Engine immobiliser system set (hybrid control system start prohibited) (power switch off) Unset: Engine immobiliser system unset (hybrid control system start permitted) (power switch on (ACC) or on (IG)) | If "Set" is displayed, the hybrid control system start function is prohibited.
|
| Master Key | Whether master key ID code matches ID code registered in certification ECU (smart key ECU assembly) / Match or No Match | Match: ID code of master key matches ID code registered in certification ECU (smart key ECU assembly) No Match: ID code of master key does not match ID code registered in certification ECU (smart key ECU assembly) | - |
| Sub Key | Whether sub key ID code matches ID code registered in certification ECU (smart key ECU assembly) / Match or No Match | Match: ID code of sub key matches ID code registered in certification ECU (smart key ECU assembly) No Match: ID code of sub key does not match ID code registered in certification ECU (smart key ECU assembly) | - |
| BCC Malfunction | BCC signal status of transponder chip*1 / OK or NG | OK: BCC signal normal NG: BCC signal malfunction (malfunction in code computation in key/certification ECU (smart key ECU assembly)) | Problems may be caused by the following:
|
| Abnormal Status | Transponder chip status signal*1 / OK or NG | OK: Transponder chip status signal normal NG: Transponder chip status signal malfunction (malfunction in code computation in key/certification ECU (smart key ECU assembly)) | Problems may be caused by the following:
|
| Different Encrypt Code | Code status between transponder chip and certification ECU (smart key ECU assembly)*1 / OK or NG | OK: Codes of transponder chip and certification ECU (smart key ECU assembly) match NG: Codes of transponder chip and certification ECU (smart key ECU assembly) do not match | Problems may be caused by the following:
|
| Different Serial Number | Vehicle serial number*1 / OK or NG | OK: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) match NG: Signal from transponder chip and vehicle serial number stored in the certification ECU (smart key ECU assembly) do not match | Problems may be caused by the following:
|
| Frame Error | State of data sent from key / OK or NG | OK: No problem with data sent from key NG: Problem with data sent from key | Problems may be caused by the following:
|
| Response | Key response to signal from certification ECU (smart key ECU assembly) / OK or NG | OK: Key responds to signal from certification ECU (smart key ECU assembly) NG: Key does not respond to signal from certification ECU (smart key ECU assembly) | Problems may be caused by the following:
|
| Engine Start Condition | Hybrid control system start permission from certification ECU (smart key ECU assembly)*2 / OK or NG | OK: Hybrid control system start permitted by certification ECU (smart key ECU assembly) NG: Hybrid control system start prohibited by certification ECU (smart key ECU assembly) | - |
| ID-BOX Sleep Condition*9 | Certification ECU (smart key ECU assembly) sleep mode status / Yes or No | Yes: Certification ECU (smart key ECU assembly) sleep mode possible No: Certification ECU (smart key ECU assembly) sleep mode not possible | - |
| ID-BOX Start Condition | Certification ECU (smart key ECU assembly) status*3 / Yes or No | Yes: Wake-up signal sent by certification ECU (smart key ECU assembly) No: Wake-up signal not sent by certification ECU (smart key ECU assembly) | - |
| Engine Start Request*9 | Request to certification ECU (smart key ECU assembly) to permit power management control ECU to start hybrid control system*4 / OK or NG | OK: Hybrid control system start permission request signal received by certification ECU (smart key ECU assembly) NG: Hybrid control system start permission request signal not received by certification ECU (smart key ECU assembly) | If OK is not displayed, the immobiliser cannot be unset by the power management control ECU. |
| 3bit Code Request | 3-bit code request condition / OK or NG | OK: 3-bit code request condition signal received NG: 3-bit code request condition signal not received | - |
| L Code Check | L code verification result*5 / OK or NG | OK: L code verification result normal NG: L code verification result abnormal | Problem may be caused by the following:
|
| Unlock Request Receive*9 | Status of steering unlock command from certification ECU (smart key ECU assembly)*6 / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of power switch turned on (ACC) or on (IG), or of hybrid control system start operation performed) NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (power switch not turned on (ACC) or on (IG), and hybrid control system start operation not performed) | If OK is not displayed even when the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Lock Request Receive*9 | Status of steering lock command from certification ECU (smart key ECU assembly)*7 / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and power switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and power switch off) | If OK is not displayed even when the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| L Code Check (Past) | L code verification result (past) / OK or NG(Past) | OK: Verification confirmed (past) NG(Past): Verification not confirmed (past) | - |
| EFI Code Receive*9 | Certification information sent to certification ECU (smart key ECU assembly) from power management control ECU when power management control ECU receives hybrid control system start permission signal from certification ECU (smart key ECU assembly)*8 / OK or NG | OK: Signal from power management control ECU to unset engine immobiliser received by certification ECU (smart key ECU assembly) NG: Signal from power management control ECU to unset engine immobiliser not received by certification ECU (smart key ECU assembly) | - |
| EFI communication | State of communication to unset immobiliser between certification ECU (smart key ECU assembly) and power management control ECU / OK or NG | OK: Communication to unset immobiliser has started between certification ECU (smart key ECU assembly) and power management control ECU NG: Communication to unset immobiliser has not started between certification ECU (smart key ECU assembly) and power management control ECU | If this item displays "NG" even though the conditions to unset the immobiliser have been met and the Engine Start Request Data List item displays "OK", the power management control ECU may be malfunctioning. When the hybrid control system cannot be started, use this Data List item during troubleshooting. |

| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Immobiliser Indicator | Security indicator light | OFF/ON | - |