Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

When there are communication malfunctions between the power management control ECU and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the power management control ECU stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*):
  1. A malfunction in the communication or communication lines between the power management control ECU and certification ECU (smart key ECU assembly).
  2. A matching communication code cannot be verified during communication between the power management control ECU and certification ECU (smart key ECU assembly).
  1. Certification ECU (smart key ECU assembly)
  2. Power management control ECU
  3. Wire harness or connector
Either condition is met:
  1. Within 10 seconds of a hybrid control system start operation (with the shift lever in P and the brake pedal depressed, the power switch is pressed while carrying the key). If there is a malfunction, the hybrid control system does not start (communication begins within 3 seconds of the hybrid control system start operation, and DTCs are stored after 6 seconds).
  2. 10 seconds after the power switch is turned on (IG) after reconnecting the cable to the negative (-) auxiliary battery terminal (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B2799
-

WIRING DIAGRAM


B271006E39


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:
When DTC B2799 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

1.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


Go to step 3

2.CHECK POWER MANAGEMENT CONTROL ECU (TERMINAL IMO)


  1. Using an oscilloscope, check the waveform.


    B384259E03


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    *c
    Approximately 160 ms
    *d
    Approximately 270 ms

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    I4-28 (IMO) - Body ground
    Turn the power switch on (READY)
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Waveform not output, or has abnormal wavelength or shape
    C



B
Go to step 6

C
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


3.CHECK POWER MANAGEMENT CONTROL ECU (TERMINAL IMI)


  1. Using an oscilloscope, check the waveform.


    B384260E02


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    *b
    Waveform
    *c
    Approximately 160 ms
    *d
    Approximately 270 ms

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    I4-29 (IMI) - Body ground
    Power switch on (IG) using registered electrical key transmitter sub-assembly
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the power switch on (IG).

  1. Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).

    OK:
    Hybrid control system starts normally.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Disconnect the I4 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I4-28 (IMO) - Body ground
    Power switch on (IG) using registered electrical key transmitter sub-assembly
    Terminal IMO stuck low (2.4 V or less)
    Terminal IMO stuck high (12 V) or abnormal waveform

    Result:
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V) or abnormal waveform
    B



B
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
A


7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the I87 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I87-10 (EFII) - I4-28 (IMO)
    Always
    Below 1 Ω
    I4-28 (IMO) - Body ground
    Always
    10 kΩ or higher
    I87-14 (EFIO) - I4-29 (IMI)
    Always
    Below 1 Ω
    I4-29 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


9.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


10.WHETHER HYBRID CONTROL SYSTEM STARTS
  1. Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the power switch on (IG).

  1. Check that the hybrid control system starts 5 seconds after the power switch turned on (IG).

    OK:
    Hybrid control system starts normally.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)