Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


5. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY
(Click here)


6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


7. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel subassembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



8. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



9. REMOVE INTAKE FLANGE


    A259344
  1. Remove the 4 bolts and intake flange.

  1. Remove the gasket.



10. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR


    A258676
  1. Disconnect the connector.



    A257328
  1. Disconnect the vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.



11. SEPARATE INTAKE MANIFOLD


    A257341
  1. Disconnect the No. 2 ventilation hose.



    A259044
  1. Disconnect the heated oxygen sensor connector.



    A257343
  1. Disconnect the 6 wire harness clamps.



    A257344
  1. Remove the 6 bolts to separate the intake manifold from the engine assembly.



12. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A259299
  1. Remove the No. 1 fuel pipe clamp.



    A259300E01
  1. Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
    Text in Illustration 
    *1
    Fuel Pipe
    *2
    Fuel Tube Connector
    *3
    Nylon Tube
    *4
    O-ring
    *5
    Retainer
    V100135
    Pinch
    V100136
    Pull

    NOTICE:
    1. Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel pipe.
    2. Do not use any tools to separate the fuel tube connector and fuel pipe.
    3. Do not forcefully bend, kink or twist the nylon tube.
    4. Keep the fuel tube connector and fuel pipe free from foreign matter.
    5. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.
    6. Put the fuel tube connector and fuel pipe in plastic bags to prevent damage and contamination.

  1. Remove the fuel tube sub-assembly from the fuel hose clamp.



13. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A259321
  1. Disconnect the 4 fuel injector connectors.

  1. Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A259322
  1. Remove the 2 fuel delivery spacers from the cylinder head.

  1. Remove the 4 injector vibration insulators from the cylinder head.



14. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold from the vehicle.



    A257345
  1. Remove the gasket from the intake manifold.



    A257346
  1. Remove the bolt and wire harness clamp bracket.



    A257347
  1. Remove the vacuum hose from the intake manifold.



    A258678
  1. Remove the fuel vapor feed hose from the intake manifold.