Home › Engine / Hybrid System › 2AR-FXE INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

HINT:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY
(Click here)


6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


7. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel subassembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



8. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



9. REMOVE INTAKE FLANGE (w/o EGR System)


  1. Type A:



      A259344
    1. Remove the 4 bolts and intake flange from the intake manifold.



  1. Type B:



      A330826
    1. Remove the 3 bolts and intake flange from the intake manifold.

  1. Remove the gasket from the intake manifold.



10. REMOVE EGR VALVE ASSEMBLY (w/ EGR System)


    A259678
  1. Disconnect the EGR valve assembly connector.



    A257329
  1. Slide the 2 clips and disconnect the 2 water by-pass hoses from the EGR valve assembly.



    A317164
  1. Using a 10 mm deep socket wrench, remove the bolt from the EGR valve assembly.

  1. Using a 12 mm deep socket wrench, remove the 2 nuts from the EGR valve assembly.



  1. Type A:



      A317165
    1. Remove the 4 bolts and EGR valve assembly from the intake manifold.



  1. Type B:



      A330824
    1. Remove the 3 bolts and EGR valve assembly from the intake manifold.



    A257332
  1. Remove the 2 gaskets from the intake manifold and No. 1 EGR pipe.



11. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR


    A258676
  1. Disconnect the connector.



    A257328
  1. Disconnect the vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.



12. SEPARATE INTAKE MANIFOLD


    A257341
  1. Slide the clip and disconnect the No. 2 ventilation hose from the intake manifold.



    A259044
  1. Disconnect the heated oxygen sensor connector.



    A257343
  1. Disengage the 6 wire harness clamps from the intake manifold.



    A257344
  1. Remove the 6 bolts to separate the intake manifold from the cylinder head sub-assembly.



13. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A259299
  1. Remove the No. 1 fuel pipe clamp.



    A259300E01
  1. Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
    Text in Illustration 
    *1
    Fuel Pipe
    *2
    Fuel Tube Connector
    *3
    Nylon Tube
    *4
    O-ring
    *5
    Retainer
    V100135
    Pinch
    V100136
    Pull

    NOTICE:
    1. Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel pipe.
    2. Do not use any tools to separate the fuel tube connector and fuel pipe.
    3. Do not forcefully bend, kink or twist the nylon tube.
    4. Keep the fuel tube connector and fuel pipe free from foreign matter.
    5. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.
    6. Put the fuel tube connector and fuel pipe in plastic bags to prevent damage and contamination.

  1. Remove the fuel tube sub-assembly from the fuel hose clamp.



14. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A259321
  1. Disconnect the 4 fuel injector connectors.

  1. Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



    A259322
  1. Remove the 2 fuel delivery spacers from the cylinder head.

  1. Remove the 4 injector vibration insulators from the cylinder head.



15. REMOVE INTAKE MANIFOLD
  1. Remove the intake manifold from the cylinder head sub-assembly.



    A257345
  1. Remove the gasket from the intake manifold.



    A257346
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A330827
  1. Disengage the clamp and remove the vacuum hose from the intake manifold.



    A258678
  1. Slide the clip and disconnect the fuel vapor feed hose from the intake manifold.