INTAKE MANIFOLD > REMOVAL |
| 1. PRECAUTION |
| 2. DISCHARGE FUEL SYSTEM PRESSURE |
| 3. REMOVE LUGGAGE TRIM SERVICE HOLE COVER |
![]() |
Disengage the claw to remove the luggage trim service hole cover.
| 4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
| 5. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY |
| 6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 7. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel subassembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 8. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 9. REMOVE INTAKE FLANGE (w/o EGR System) |
Type A:
![]() |
Remove the 4 bolts and intake flange from the intake manifold.
Type B:
![]() |
Remove the 3 bolts and intake flange from the intake manifold.
Remove the gasket from the intake manifold.
| 10. REMOVE EGR VALVE ASSEMBLY (w/ EGR System) |
![]() |
Disconnect the EGR valve assembly connector.
![]() |
Slide the 2 clips and disconnect the 2 water by-pass hoses from the EGR valve assembly.
![]() |
Using a 10 mm deep socket wrench, remove the bolt from the EGR valve assembly.
Using a 12 mm deep socket wrench, remove the 2 nuts from the EGR valve assembly.
Type A:
![]() |
Remove the 4 bolts and EGR valve assembly from the intake manifold.
Type B:
![]() |
Remove the 3 bolts and EGR valve assembly from the intake manifold.
![]() |
Remove the 2 gaskets from the intake manifold and No. 1 EGR pipe.
| 11. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR |
![]() |
Disconnect the connector.
![]() |
Disconnect the vacuum hose.
Remove the bolt and manifold absolute pressure sensor.
| 12. SEPARATE INTAKE MANIFOLD |
![]() |
Slide the clip and disconnect the No. 2 ventilation hose from the intake manifold.
![]() |
Disconnect the heated oxygen sensor connector.
![]() |
Disengage the 6 wire harness clamps from the intake manifold.
![]() |
Remove the 6 bolts to separate the intake manifold from the cylinder head sub-assembly.
| 13. DISCONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 1 fuel pipe clamp.
![]() |
Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.
| *1 | Fuel Pipe |
| *2 | Fuel Tube Connector |
| *3 | Nylon Tube |
| *4 | O-ring |
| *5 | Retainer |
![]() | Pinch |
![]() | Pull |
Remove the fuel tube sub-assembly from the fuel hose clamp.
| 14. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 4 fuel injector connectors.
Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.
![]() |
Remove the 2 fuel delivery spacers from the cylinder head.
Remove the 4 injector vibration insulators from the cylinder head.
| 15. REMOVE INTAKE MANIFOLD |
Remove the intake manifold from the cylinder head sub-assembly.
![]() |
Remove the gasket from the intake manifold.
![]() |
Remove the bolt and wire harness clamp bracket from the intake manifold.
![]() |
Disengage the clamp and remove the vacuum hose from the intake manifold.
![]() |
Slide the clip and disconnect the fuel vapor feed hose from the intake manifold.